Part templates reference
Every Part Wizard template, with every field it asks for, where in the datasheet to find it, and the live-model parameter it sets. Columns says which of min, typ and max the field takes. Required fields are marked *. Sets names the simulation parameter the value feeds, where it feeds one directly. The others are kept in the part file and used by checks, reports and the datasheet limits.
The template files are in parts/templates. A template's kind becomes the device type shown after the arrow when the part is placed.
55.1Analog ICs
Analog · 555 timer (analog.timer555 → device timer555)
Simulation pins: gnd, trig, out, reset, ctrl, thr, dis, vcc.
| Field | Symbol | Unit | Columns | Sets | Where to find it in the datasheet |
|---|---|---|---|---|---|
| Supply voltage range * | V_CC | V | min, max | Recommended Operating Conditions, row "Supply Voltage" (V_CC). | |
| Supply current | I_CC | A | typ, max | Electrical Characteristics, row "Supply Current" with output low, no load, at V_CC = 5 V and 15 V. | |
| Threshold voltage (fraction of V_CC) | V_TH/V_CC | typ | Electrical Characteristics, row "Threshold Voltage Level" divided by V_CC (nominally 2/3). | ||
| Trigger voltage (fraction of V_CC) | V_TRIG/V_CC | typ | Electrical Characteristics, row "Trigger Voltage Level" divided by V_CC (nominally 1/3). | ||
| Output high drop below V_CC | V_CC − V_OH | V | typ, max | Electrical Characteristics, row "High-Level Output Voltage" at I_OH = −100 mA: V_CC minus that value (≈1.7 V for bipolar, ≈0 for CMOS). | |
| Output low voltage | V_OL | V | typ, max | Electrical Characteristics, row "Low-Level Output Voltage" at I_OL = 10 mA..100 mA. | |
| Output current | I_O | A | max | Absolute Maximum Ratings, row "Output Current" (±200 mA for NE555). | |
| Output rise time | t_r | s | typ | Switching Characteristics, row "Output Pulse Rise Time". | |
| Maximum astable frequency | f_max | Hz | typ | Electrical Characteristics, row "Maximum Frequency" in astable mode (typ). | |
| Initial timing error | Δt/t | % | typ, max | Electrical Characteristics, row "Timing Error, Initial Accuracy" (monostable and astable rows). | |
| Threshold current | I_THR | A | typ, max | Electrical Characteristics, row "Threshold Current". | |
| Trigger current | I_TRIG | A | typ, max | Electrical Characteristics, row "Trigger Current". | |
| Reset current | I_RST | A | typ, max | Electrical Characteristics, row "Reset Current". | |
| Discharge on-resistance | R_DIS | Ohm | typ | Electrical Characteristics, row "Discharge Switch On-State Voltage" divided by the stated current, or "Discharge Saturation Voltage". | |
| Timing drift with temperature | Δt/ΔT | ppm/C | typ | Electrical Characteristics, row "Temperature Drift of Timing". | |
| Timing drift with supply | Δt/ΔV | %/V | typ | Electrical Characteristics, row "Drift With Supply Voltage". | |
| Thermal resistance, junction to ambient | θ_JA | C/W | typ, max | Thermal Characteristics / Thermal Information table, row "Junction-to-Ambient" (R_θJA). Note the PCB it is quoted on (JEDEC 1s or 2s2p). | |
| Thermal resistance, junction to case | θ_JC | C/W | typ, max | Thermal Characteristics table, row "Junction-to-Case" (R_θJC). For power packages use the tab / bottom value. | |
| Maximum junction temperature | T_J(max) | C | max | Absolute Maximum Ratings table, row "Junction Temperature" or "Operating Junction Temperature" (T_J). | |
| Power dissipation | P_D | W | max | Absolute Maximum Ratings, row "Power Dissipation" (P_D or P_tot) at T_A = 25 °C. If only a derating curve exists read its 25 °C value. | |
| Pin count | N_pins | typ | Package / Pin Configuration drawing on page 1 or 2. Count every terminal including the exposed pad. |
Analog · Comparator (analog.comparator → device comparator)
Simulation pins: in+, in-, out, v+, v-. Curves: Propagation delay vs input overdrive, Output low voltage vs sink current, Supply current vs supply voltage.
| Field | Symbol | Unit | Columns | Sets | Where to find it in the datasheet |
|---|---|---|---|---|---|
| Supply voltage range (total) | V_S | V | min, max | Recommended Operating Conditions, row "Supply Voltage". | |
| Propagation delay * | t_PD | s | typ, max | Switching Characteristics, row "Response Time" or "Propagation Delay" with the stated overdrive (for example 5 mV or 100 mV) and pull-up. | |
| Input hysteresis | V_HYST | V | typ | Electrical Characteristics, row "Input Hysteresis". 0 when the part has none (most LM393-class parts). | |
| Open-drain / open-collector output (1 = yes) * | OD | typ | Block diagram or pin description: an output transistor with no internal pull-up means open collector / drain (1). Push-pull is 0. | ||
| Input offset voltage | V_OS | V | typ, max | Electrical Characteristics, row "Input Offset Voltage" at 25 °C. | |
| Input bias current | I_B | A | typ, max | Electrical Characteristics, row "Input Bias Current". | |
| Supply current | I_Q | A | typ, max | Electrical Characteristics, row "Supply Current" (per comparator). | |
| Output sink current | I_SINK | A | min | Electrical Characteristics, row "Output Sink Current" at V_O = 1.5 V. | |
| Output low voltage | V_OL | V | typ, max | Electrical Characteristics, row "Low-Level Output Voltage" at the stated sink current. | |
| Input offset current | I_OS | A | typ, max | Electrical Characteristics, row "Input Offset Current". | |
| Common-mode range beyond the rail | V_ICM | V | typ | Electrical Characteristics, row "Input Common-Mode Voltage Range": how far past each supply the inputs may go (negative = inside the rail). | |
| Output leakage (open-drain high) | I_OH | A | max | Electrical Characteristics, row "Output Leakage Current" (open-drain or open-collector outputs). | |
| Common-mode rejection ratio | CMRR | dB | min, typ | Electrical Characteristics, row "Common-Mode Rejection Ratio". | |
| Power-supply rejection ratio | PSRR | dB | min, typ | Electrical Characteristics, row "Power-Supply Rejection Ratio". | |
| Power-on delay | t_on | s | typ | Electrical Characteristics, row "Power-On Time" or "Turn-On Delay". | |
| Thermal resistance, junction to ambient | θ_JA | C/W | typ, max | Thermal Characteristics / Thermal Information table, row "Junction-to-Ambient" (R_θJA). Note the PCB it is quoted on (JEDEC 1s or 2s2p). | |
| Thermal resistance, junction to case | θ_JC | C/W | typ, max | Thermal Characteristics table, row "Junction-to-Case" (R_θJC). For power packages use the tab / bottom value. | |
| Maximum junction temperature | T_J(max) | C | max | Absolute Maximum Ratings table, row "Junction Temperature" or "Operating Junction Temperature" (T_J). | |
| Power dissipation | P_D | W | max | Absolute Maximum Ratings, row "Power Dissipation" (P_D or P_tot) at T_A = 25 °C. If only a derating curve exists read its 25 °C value. | |
| Pin count | N_pins | typ | Package / Pin Configuration drawing on page 1 or 2. Count every terminal including the exposed pad. |
Analog · Current-sense amplifier (analog.csa → device csa)
Simulation pins: IN+, IN−, OUT, VS, GND. Symbol variants: uni, bidir, hs. Curves: Gain vs frequency.
| Field | Symbol | Unit | Columns | Sets | Where to find it in the datasheet |
|---|---|---|---|---|---|
| Gain * | G | V/V | typ | gain | Gain option of the part number (INA180A1 = 20, A2 = 50, A3 = 100, A4 = 200). |
| Bandwidth | BW | Hz | typ | bw | "Bandwidth" (−3 dB) at your gain. |
| Offset voltage | V_OS | V | typ, max | vos | "Offset voltage, RTI". |
| Common-mode range | V_CM | V | min, max | vcm_max | "Common-mode input range". |
| Gain error | ε_G | % | typ, max | Electrical Characteristics, row "Gain Error". | |
| Offset voltage drift | ΔV_OS/ΔT | V/C | typ, max | Electrical Characteristics, row "Offset Voltage Drift". | |
| Common-mode rejection ratio | CMRR | dB | min, typ | Electrical Characteristics, row "CMRR". | |
| Power-supply rejection ratio | PSRR | dB | min, typ | Electrical Characteristics, row "PSRR". | |
| Quiescent current | I_Q | A | typ, max | Electrical Characteristics, row "Quiescent Current". | |
| Operating temperature range | T_op | C | min, max | Features or Recommended Operating Conditions, row "Operating Temperature Range" (minimum and maximum). | |
| Pin count | N_pins | typ | Package / Pin Configuration drawing on page 1 or 2. Count every terminal including the exposed pad. |
Analog · Instrumentation amplifier (analog.inamp → device inamp)
Simulation pins: in+, in−, rg1, rg2, ref, out, v+, v−. Symbol variants: rg, fixed, diff. Curves: CMRR vs frequency, Gain vs frequency.
| Field | Symbol | Unit | Columns | Sets | Where to find it in the datasheet |
|---|---|---|---|---|---|
| Gain-equation resistor | R_F | Ohm | typ | rf | Gain equation: G = 1 + 49.4 kΩ / R_G → R_F = 24.7 kΩ (AD620). INA128: 50 kΩ / R_G → 25 kΩ. |
| Fixed gain | G | V/V | typ | gain | Fixed-gain parts / difference amps: "Gain". |
| Gain-bandwidth | GBW | Hz | typ | gbw | "Bandwidth" at G = 1 or GBW. |
| Slew rate | SR | V/s | typ | slew | "Slew rate" (V/µs × 1e6). |
| Input offset voltage | V_OS | V | typ, max | vos | "Input offset voltage" (RTI). |
| CMRR | CMRR | dB | min, typ | cmrr_db | "Common-mode rejection" at your gain. |
| Quiescent current | I_Q | A | typ, max | iq | "Quiescent current". |
| Offset voltage drift | ΔV_OS/ΔT | V/C | typ, max | Electrical Characteristics, row "Offset Voltage Drift" (µV/°C). | |
| Input bias current | I_B | A | typ, max | Electrical Characteristics, row "Input Bias Current". | |
| Gain error | ε_G | % | typ, max | Electrical Characteristics, row "Gain Error" at the stated gain. | |
| Gain nonlinearity | NL | ppm | typ, max | Electrical Characteristics, row "Nonlinearity". | |
| Power-supply rejection ratio | PSRR | dB | min, typ | Electrical Characteristics, row "PSRR". | |
| Operating temperature range | T_op | C | min, max | Features or Recommended Operating Conditions, row "Operating Temperature Range" (minimum and maximum). | |
| Input voltage noise density | e_n | V/rtHz | typ | Electrical Characteristics, row "Voltage Noise Density" at 1 kHz. | |
| Pin count | N_pins | typ | Package / Pin Configuration drawing on page 1 or 2. Count every terminal including the exposed pad. |
Analog · Multiplier (analog.mult → device mult)
Simulation pins: x1, x2, y1, y2, z, w, v+, v−.
| Field | Symbol | Unit | Columns | Sets | Where to find it in the datasheet |
|---|---|---|---|---|---|
| Scale factor | SF | V | typ | scale | Transfer function W = (X1 − X2)(Y1 − Y2) / SF + Z (AD633: 10 V). |
| Bandwidth | BW | Hz | typ | bw | "Small-signal bandwidth". |
| Operating temperature range | T_op | C | min, max | Features or Recommended Operating Conditions, row "Operating Temperature Range" (minimum and maximum). | |
| Pin count | N_pins | typ | Package / Pin Configuration drawing on page 1 or 2. Count every terminal including the exposed pad. |
Analog · Op-amp (analog.opamp → device opamp)
Simulation pins: in+, in-, out, v+, v-. Symbol variants: 5pin, 3pin, 8pin, sd. Curves: Open-loop gain vs frequency, CMRR vs frequency, PSRR vs frequency, Voltage noise vs frequency, Open-loop phase vs frequency, Output impedance vs frequency, Output swing from the rail vs load current, Input bias current vs temperature, Offset voltage vs temperature, Supply current vs supply voltage.
| Field | Symbol | Unit | Columns | Sets | Where to find it in the datasheet |
|---|---|---|---|---|---|
| Supply voltage range (total) | V_S | V | min, max | Recommended Operating Conditions, row "Supply Voltage" (V_S = V+ − V−. ±15 V means 30 V). | |
| Open-loop voltage gain * | A_OL | dB | min, typ | Electrical Characteristics, row "Large-Signal Voltage Gain" (A_VD or A_OL). Convert V/mV to dB: 20·log10(V/mV × 1000). | |
| Gain-bandwidth product * | GBW | Hz | min, typ | Electrical Characteristics, row "Gain Bandwidth Product" (GBW, or unity-gain bandwidth B_1). | |
| Slew rate * | SR | V/s | min, typ | Electrical Characteristics, row "Slew Rate" (V/µs. Store in V/s, 13 V/µs = 1.3e7) at unity gain. | |
| Input offset voltage | V_OS | V | typ, max | Electrical Characteristics, row "Input Offset Voltage" at 25 °C (the full-range value is larger). | |
| Input bias current | I_B | A | typ, max | Electrical Characteristics, row "Input Bias Current" at 25 °C. | |
| Input offset current | I_OS | A | typ, max | Electrical Characteristics, row "Input Offset Current". | |
| Supply current per amplifier | I_Q | A | typ, max | Electrical Characteristics, row "Supply Current" (no load). Divide by the number of amplifiers if the row says "all amplifiers". | |
| Output headroom to the rails | V_DROP | V | typ | Electrical Characteristics, rows "Output Voltage Swing" V_OH / V_OL: headroom = V+ − V_OH at your load. 0 for rail-to-rail output. | |
| Input common-mode headroom | V_ICR | V | typ | Electrical Characteristics, row "Common-Mode Input Voltage Range": distance from the positive rail to the top of the range. | |
| Open-loop output resistance | R_O | Ohm | typ | Row "Open-Loop Output Impedance" or the Z_O vs frequency graph at low frequency. Often absent (use 50 to 100 Ω). | |
| Short-circuit output current | I_SC | A | typ | Electrical Characteristics, row "Short-Circuit Output Current". | |
| Offset voltage drift | ΔV_OS/ΔT | V/C | typ, max | Electrical Characteristics, row "Input Offset Voltage Drift" (µV/°C). Type 2u for 2 µV/°C. | |
| Differential input resistance | R_IN(dm) | Ohm | typ | Electrical Characteristics, row "Input Resistance, Differential". | |
| Common-mode input resistance | R_IN(cm) | Ohm | typ | Electrical Characteristics, row "Input Resistance, Common-Mode". | |
| Input capacitance | C_IN | F | typ | Electrical Characteristics, row "Input Capacitance" (differential or common-mode, say which in the note). | |
| Rail-to-rail input (1 = yes) | RRI | typ | Front page feature list: "Rail-to-rail input" gives 1, otherwise 0. Check the common-mode range row for the real limits. | ||
| Rail-to-rail output (1 = yes) | RRO | typ | Front page feature list: "Rail-to-rail output" gives 1, otherwise 0. The swing row has the real headroom. | ||
| Settling time | t_s | s | typ | Electrical Characteristics, row "Settling Time" to 0.1 % or 0.01 % (say which in the note). | |
| Turn-on time | t_on | s | typ | Electrical Characteristics, row "Turn-On Time" or "Start-Up Time". | |
| Phase margin | φ_m | deg | typ | Row "Phase Margin" or the Open-Loop Gain and Phase graph at the unity-gain frequency. | |
| Capacitive load for stability | C_L(max) | F | typ | Typical Characteristics, "Small-Signal Overshoot vs Capacitive Load", or the applications note: the largest load with no oscillation. | |
| Input voltage noise density | e_n | V/rtHz | typ | Electrical Characteristics, row "Input Voltage Noise Density" (nV/√Hz) at 1 kHz. | |
| Input current noise density | i_n | A/rtHz | typ | Electrical Characteristics, row "Input Current Noise Density" (fA/√Hz or pA/√Hz) at 1 kHz. | |
| Common-mode rejection ratio | CMRR | dB | min, typ | Electrical Characteristics, row "Common-Mode Rejection Ratio" (DC). | |
| Power-supply rejection ratio | PSRR | dB | min, typ | Electrical Characteristics, row "Supply-Voltage Rejection Ratio" (k_SVR or PSRR, DC). | |
| Noise 0.1 to 10 Hz, peak to peak | e_n(pp) | V | typ | Electrical Characteristics, row "Input Voltage Noise, 0.1 Hz to 10 Hz" (µV p-p). | |
| 1/f noise corner frequency | f_c | Hz | typ | Typical Characteristics, "Input Voltage Noise Density vs Frequency": the frequency where the density has fallen to 1.41 times its flat value. | |
| Total harmonic distortion plus noise | THD+N | % | typ | Electrical Characteristics, row "THD+N" with f, gain and output level in the conditions. | |
| Thermal resistance, junction to ambient | θ_JA | C/W | typ, max | Thermal Characteristics / Thermal Information table, row "Junction-to-Ambient" (R_θJA). Note the PCB it is quoted on (JEDEC 1s or 2s2p). | |
| Thermal resistance, junction to case | θ_JC | C/W | typ, max | Thermal Characteristics table, row "Junction-to-Case" (R_θJC). For power packages use the tab / bottom value. | |
| Maximum junction temperature | T_J(max) | C | max | Absolute Maximum Ratings table, row "Junction Temperature" or "Operating Junction Temperature" (T_J). | |
| Power dissipation | P_D | W | max | Absolute Maximum Ratings, row "Power Dissipation" (P_D or P_tot) at T_A = 25 °C. If only a derating curve exists read its 25 °C value. | |
| Pin count | N_pins | typ | Package / Pin Configuration drawing on page 1 or 2. Count every terminal including the exposed pad. |
Analog · OTA (analog.ota → device ota)
Simulation pins: in+, in−, iabc, out, v+, v−.
| Field | Symbol | Unit | Columns | Sets | Where to find it in the datasheet |
|---|---|---|---|---|---|
| Transconductance per I_ABC | g_m/I_ABC | 1/V | typ | "Forward transconductance" vs I_ABC graph (≈ 19.2 /V at 25 °C). | |
| Max amplifier bias current | I_ABC | A | max | Absolute maximum, "Amplifier bias current" (informational). | |
| Operating temperature range | T_op | C | min, max | Features or Recommended Operating Conditions, row "Operating Temperature Range" (minimum and maximum). | |
| Pin count | N_pins | typ | Package / Pin Configuration drawing on page 1 or 2. Count every terminal including the exposed pad. |
Analog · Voltage reference (analog.reference → device vref)
Simulation pins: out, gnd. Symbol variants: shunt. Curves: Reference voltage vs temperature, Output impedance vs frequency, Noise density vs frequency, Cathode current vs cathode voltage (shunt).
| Field | Symbol | Unit | Columns | Sets | Where to find it in the datasheet |
|---|---|---|---|---|---|
| Reference voltage * | V_REF | V | min, typ, max | Electrical Characteristics, row "Reference Voltage" (V_REF, or V_KA = V_REF for shunt references) at 25 °C and the stated cathode current. | |
| Output / dynamic impedance | Z_KA | Ohm | typ, max | Electrical Characteristics, row "Dynamic Impedance" (|Z_KA|) for shunt types, or "Load Regulation" (ΔV / ΔI) for series types. | |
| Minimum cathode current | I_K(min) | A | max | Electrical Characteristics, row "Minimum Cathode Current for Regulation" (shunt types). | |
| Maximum cathode / output current | I_K(max) | A | max | Recommended Operating Conditions, row "Cathode Current" (shunt) or "Output Current" (series). | |
| Maximum cathode voltage | V_KA | V | max | Recommended Operating Conditions, row "Cathode Voltage" (adjustable shunt types). | |
| Temperature drift | TC | ppm/C | typ, max | Electrical Characteristics, row "Temperature Coefficient" (ppm/°C), or derive from "V_REF deviation over temperature" ÷ (V_REF · ΔT). | |
| Reference input current | I_REF | A | typ, max | Electrical Characteristics, row "Reference Input Current" (adjustable shunt types). | |
| Initial accuracy | ΔV_REF | % | typ, max | Electrical Characteristics, row "Initial Accuracy" or "Output Voltage Tolerance" at 25 °C. | |
| Line regulation | ΔV/ΔV_IN | %/V | typ, max | Electrical Characteristics, row "Line Regulation". | |
| Load regulation | ΔV/ΔI | V/A | typ, max | Electrical Characteristics, row "Load Regulation" (mV/mA is the same as V/A: type 0.2 for 0.2 mV/mA). | |
| Supply current | I_Q | A | typ, max | Electrical Characteristics, row "Supply Current" or "Quiescent Current" (series references). | |
| Maximum load current | I_L | A | max | Electrical Characteristics, row "Output Current" (sourcing, and sinking if listed). | |
| Long-term drift | ΔV/Δt | ppm | typ | Electrical Characteristics, row "Long-Term Stability" (ppm per 1000 h). | |
| Thermal hysteresis | ΔV_hys | ppm | typ | Electrical Characteristics, row "Thermal Hysteresis". | |
| Output noise | e_n | V | typ | Electrical Characteristics, row "Output Noise Voltage" (µVrms or µVpp), note the bandwidth (0.1 to 10 Hz or 10 Hz to 10 kHz). | |
| Thermal resistance, junction to ambient | θ_JA | C/W | typ, max | Thermal Characteristics / Thermal Information table, row "Junction-to-Ambient" (R_θJA). Note the PCB it is quoted on (JEDEC 1s or 2s2p). | |
| Thermal resistance, junction to case | θ_JC | C/W | typ, max | Thermal Characteristics table, row "Junction-to-Case" (R_θJC). For power packages use the tab / bottom value. | |
| Maximum junction temperature | T_J(max) | C | max | Absolute Maximum Ratings table, row "Junction Temperature" or "Operating Junction Temperature" (T_J). | |
| Power dissipation | P_D | W | max | Absolute Maximum Ratings, row "Power Dissipation" (P_D or P_tot) at T_A = 25 °C. If only a derating curve exists read its 25 °C value. | |
| Pin count | N_pins | typ | Package / Pin Configuration drawing on page 1 or 2. Count every terminal including the exposed pad. |
55.2Any device
Any device · Device type of your choice (generic.device → device of your choice)
A part of any of the 165 device types the engine simulates. It has no datasheet fields: the Part Wizard asks for the device's own parameters (the inspector's fields), saved in model.live.p, and maps its pins like any other part.
Simulation pins: none.
55.3Audio
Audio · Audio amplifier (audio.audioamp → device audioamp)
Simulation pins: IN+, IN−, OUT+, OUT−, VDD, GND, SD. Symbol variants: btl, se, lm386.
| Field | Symbol | Unit | Columns | Sets | Where to find it in the datasheet |
|---|---|---|---|---|---|
| Voltage gain * | A_V | V/V | typ | gain | Electrical characteristics, "Gain" (dB → 10^(dB/20)). LM386: 20 / 200. |
| Output power | P_O | W | typ | pout | "Output power at THD+N = 10 %" and the load. |
| Quiescent current | I_Q | A | typ, max | iq | "Quiescent current". |
| Efficiency | η | typ | eff | "Efficiency" at rated power. | |
| Supply range | V_DD | V | min, max | Recommended operating conditions. | |
| Operating temperature range | T_op | C | min, max | Features or Recommended Operating Conditions, row "Operating Temperature Range" (minimum and maximum). | |
| Pin count | N_pins | typ | Package / Pin Configuration drawing on page 1 or 2. Count every terminal including the exposed pad. | ||
| Thermal resistance, junction to ambient | θ_JA | C/W | typ, max | Thermal characteristics table, "Thermal resistance junction to ambient". |
Audio · Buzzer (audio.buzzer → device buzzer)
Simulation pins: +, −. Symbol variants: magnetic, piezo, active, active_piezo.
| Field | Symbol | Unit | Columns | Sets | Where to find it in the datasheet |
|---|---|---|---|---|---|
| Resonant / rated frequency * | f_0 | Hz | typ | f0 | Specification, "Resonant frequency" / "Oscillation frequency". |
| Rated voltage | V_N | V | min, typ, max | v_rated | Specification, "Rated voltage" / "Operating voltage". |
| Rated current | I_N | A | max | i_rated | Specification, "Current consumption" at rated voltage. |
| Coil resistance (magnetic) | R | Ohm | typ | r | Magnetic transducers: "Coil resistance". |
| Capacitance (piezo) | C | F | typ | c | Piezo elements: "Capacitance at 1 kHz". |
| Sound pressure level | SPL | dB | min | "Sound output at 10 cm" (informational). | |
| Operating temperature range | T_op | C | min, max | Features or Recommended Operating Conditions, row "Operating Temperature Range" (minimum and maximum). | |
| Pin count | N_pins | typ | Package / Pin Configuration drawing on page 1 or 2. Count every terminal including the exposed pad. |
Audio · Microphone (audio.mic → device mic)
Simulation pins: out, gnd. Symbol variants: electret, mems_analog, mems_pdm.
| Field | Symbol | Unit | Columns | Sets | Where to find it in the datasheet |
|---|---|---|---|---|---|
| Sensitivity * | S | dBV/Pa | typ | sens | Specification, "Sensitivity" at 1 kHz, 94 dB SPL (dBV/Pa. DBFS for PDM). |
| Current consumption | I_D | A | max | i_d | "Current consumption" (electret: at the standard load). |
| Supply / operating voltage | V_S | V | min, typ, max | "Standard operating voltage". | |
| Signal-to-noise ratio | SNR | dB | typ | "S/N ratio" (informational). | |
| Operating temperature range | T_op | C | min, max | Features or Recommended Operating Conditions, row "Operating Temperature Range" (minimum and maximum). | |
| Pin count | N_pins | typ | Package / Pin Configuration drawing on page 1 or 2. Count every terminal including the exposed pad. |
Audio · Speaker (audio.speaker → device speaker)
Simulation pins: +, −.
| Field | Symbol | Unit | Columns | Sets | Where to find it in the datasheet |
|---|---|---|---|---|---|
| Nominal impedance * | Z | Ohm | typ | z | Specification, "Impedance". |
| DC resistance | R_e | Ohm | typ | re | Thiele–Small table, "Re". |
| Resonance frequency | f_s | Hz | typ | fs | Specification, "Resonance frequency F0 / Fs". |
| Voice-coil inductance | L_e | H | typ | le | Thiele–Small table, "Le". |
| Mechanical Q | Q_ms | typ | qms | Thiele–Small table, "Qms". | |
| Electrical Q | Q_es | typ | qes | Thiele–Small table, "Qes". | |
| Rated power | P | W | max | p_rated | "Rated input power". |
| Operating temperature range | T_op | C | min, max | Features or Recommended Operating Conditions, row "Operating Temperature Range" (minimum and maximum). | |
| Pin count | N_pins | typ | Package / Pin Configuration drawing on page 1 or 2. Count every terminal including the exposed pad. |
55.4Connectors and mechanical
Connectors · Connector (connectors.conn → device conn)
Simulation pins: 1, 2, 3, 4. Symbol variants: 1xN, 2xN, usb_c, usb_micro, usb_a, barrel, trs, trs_sw, rj45, sma, microsd, bat_holder, banana.
| Field | Symbol | Unit | Columns | Sets | Where to find it in the datasheet |
|---|---|---|---|---|---|
| Number of positions * | N | typ | n | Part number / drawing, "Number of positions / contacts". | |
| Pitch | p | m | typ | Drawing, "Pitch" (informational). | |
| Current rating per contact | I | A | max | Electrical, "Current rating" (informational). | |
| Contact resistance | R_C | Ohm | max | r_contact | Electrical, "Contact resistance" (used only when mated with r_contact >. 0). |
| Operating temperature range | T_op | C | min, max | Features or Recommended Operating Conditions, row "Operating Temperature Range" (minimum and maximum). |
Connectors · Fiducial (connectors.fiducial → device fiducial)
Simulation pins: anchor. Symbol variants: global, local.
| Field | Symbol | Unit | Columns | Sets | Where to find it in the datasheet |
|---|---|---|---|---|---|
| Copper diameter | d | m | typ | Board drawing (informational). |
Connectors · Jumper / solder jumper (connectors.jumper → device jumper)
Simulation pins: a, b. Symbol variants: open, closed, 3way, link0.
| Field | Symbol | Unit | Columns | Sets | Where to find it in the datasheet |
|---|---|---|---|---|---|
| Resistance when closed | R | Ohm | max | r | 0 Ω link datasheet, "Resistance" (≤ 50 mΩ typical). |
| Rated current | I_R | A | max | 0 Ω link: "Rated current" (informational). | |
| Pin count | N_pins | typ | Package / Pin Configuration drawing on page 1 or 2. Count every terminal including the exposed pad. |
Connectors · Mounting hole (connectors.mhole → device mhole)
Simulation pins: mh. Symbol variants: pad, np.
| Field | Symbol | Unit | Columns | Sets | Where to find it in the datasheet |
|---|---|---|---|---|---|
| Hole diameter | d | m | typ | Mechanical drawing (informational). |
Connectors · Net tie (connectors.net_tie → device net_tie)
Simulation pins: a, b. Symbol variants: 2, 3.
| Field | Symbol | Unit | Columns | Sets | Where to find it in the datasheet |
|---|---|---|---|---|---|
| Pin count | N_pins | typ | Package / Pin Configuration drawing on page 1 or 2. Count every terminal including the exposed pad. |
Connectors · Test point (connectors.tp → device tp)
Simulation pins: tp. Symbol variants: pad, loop.
| Field | Symbol | Unit | Columns | Sets | Where to find it in the datasheet |
|---|---|---|---|---|---|
| Pin count | N_pins | typ | Package / Pin Configuration drawing on page 1 or 2. Count every terminal including the exposed pad. |
55.5Data converters
Converter · ADC (converter.adc → device adc)
Simulation pins: ain, clk, d, gnd.
| Field | Symbol | Unit | Columns | Sets | Where to find it in the datasheet |
|---|---|---|---|---|---|
| Resolution * | N | bit | typ | Electrical Characteristics, row "Resolution" (bits, no missing codes). | |
| Sample rate * | f_S | Hz | max | Electrical Characteristics, row "Throughput Rate" / "Sample Rate" (max). | |
| Reference / full-scale voltage * | V_REF | V | min, typ, max | Electrical Characteristics, row "Reference Input Voltage" or "Full-Scale Input Range". | |
| Sigma-delta architecture (1 = yes) | ΣΔ | typ | Title / functional description: SAR, pipeline (0) or sigma-delta (1). | ||
| Integral non-linearity | INL | LSB | typ, max | Electrical Characteristics, row "Integral Nonlinearity". | |
| Differential non-linearity | DNL | LSB | typ, max | Electrical Characteristics, row "Differential Nonlinearity". | |
| Signal-to-noise ratio | SNR | dB | min, typ | AC Characteristics, row "SNR" at the stated input frequency. | |
| Effective number of bits | ENOB | bit | min, typ | AC Characteristics, row "ENOB" (or (SINAD − 1.76) / 6.02). | |
| Conversion latency | t_LAT | s | typ | Timing: conversion time (SAR) or digital filter latency (sigma-delta). | |
| Supply current | I_DD | A | typ, max | Electrical Characteristics, row "Supply Current" at full rate. | |
| Signal-to-noise-and-distortion | SINAD | dB | typ | Dynamic Performance table, row "SINAD" at the stated input frequency. | |
| Spurious-free dynamic range | SFDR | dB | typ | Dynamic Performance table, row "SFDR". | |
| Total harmonic distortion | THD | dB | typ | Dynamic Performance table, row "THD" (negative dB). | |
| Gain error | E_G | % | typ, max | DC Accuracy table, row "Gain Error". | |
| Offset error | E_OS | V | typ, max | DC Accuracy table, row "Offset Error". | |
| Aperture jitter | t_j | s | typ | Dynamic Performance or Timing table, row "Aperture Jitter". | |
| Power consumption | P | W | typ | Electrical Characteristics, row "Power Dissipation" at the stated rate. | |
| Thermal resistance, junction to ambient | θ_JA | C/W | typ, max | Thermal Characteristics / Thermal Information table, row "Junction-to-Ambient" (R_θJA). Note the PCB it is quoted on (JEDEC 1s or 2s2p). | |
| Thermal resistance, junction to case | θ_JC | C/W | typ, max | Thermal Characteristics table, row "Junction-to-Case" (R_θJC). For power packages use the tab / bottom value. | |
| Maximum junction temperature | T_J(max) | C | max | Absolute Maximum Ratings table, row "Junction Temperature" or "Operating Junction Temperature" (T_J). | |
| Power dissipation | P_D | W | max | Absolute Maximum Ratings, row "Power Dissipation" (P_D or P_tot) at T_A = 25 °C. If only a derating curve exists read its 25 °C value. | |
| Pin count | N_pins | typ | Package / Pin Configuration drawing on page 1 or 2. Count every terminal including the exposed pad. |
Converter · DAC (converter.dac → device dac)
Simulation pins: d, out, gnd.
| Field | Symbol | Unit | Columns | Sets | Where to find it in the datasheet |
|---|---|---|---|---|---|
| Resolution * | N | bit | typ | Electrical Characteristics, row "Resolution". | |
| Reference / full-scale voltage * | V_REF | V | min, typ, max | Electrical Characteristics, row "Reference Voltage" or "Full-Scale Output". | |
| Settling time * | t_S | s | typ, max | AC Characteristics, row "Settling Time" (to ±0.5 LSB, full-scale step). | |
| Integral non-linearity | INL | LSB | typ, max | Electrical Characteristics, row "Relative Accuracy" / "INL". | |
| Differential non-linearity | DNL | LSB | typ, max | Electrical Characteristics, row "DNL" (guaranteed monotonic if <. 1 LSB). | |
| Glitch impulse | Q_G | Vs | typ | AC Characteristics, row "Digital-to-Analog Glitch Impulse" (nV·s). | |
| Output noise density | e_n | V/rtHz | typ | Electrical Characteristics, row "Output Noise Density" at 1 kHz. | |
| Output resistance | R_OUT | Ohm | typ | Electrical Characteristics, row "Output Impedance" (buffered DACs: DC output resistance). | |
| Output slew rate | SR | V/s | typ | AC Characteristics, row "Slew Rate" (V/µs → V/s). | |
| Gain error | E_G | % | typ, max | DC Accuracy table, row "Gain Error". | |
| Offset error | E_OS | V | typ, max | DC Accuracy table, row "Offset Error". | |
| Power-supply rejection | PSRR | dB | typ | Electrical Characteristics, row "PSRR". | |
| Supply current | I_Q | A | typ, max | Electrical Characteristics, row "Supply Current". | |
| Thermal resistance, junction to ambient | θ_JA | C/W | typ, max | Thermal Characteristics / Thermal Information table, row "Junction-to-Ambient" (R_θJA). Note the PCB it is quoted on (JEDEC 1s or 2s2p). | |
| Thermal resistance, junction to case | θ_JC | C/W | typ, max | Thermal Characteristics table, row "Junction-to-Case" (R_θJC). For power packages use the tab / bottom value. | |
| Maximum junction temperature | T_J(max) | C | max | Absolute Maximum Ratings table, row "Junction Temperature" or "Operating Junction Temperature" (T_J). | |
| Power dissipation | P_D | W | max | Absolute Maximum Ratings, row "Power Dissipation" (P_D or P_tot) at T_A = 25 °C. If only a derating curve exists read its 25 °C value. | |
| Pin count | N_pins | typ | Package / Pin Configuration drawing on page 1 or 2. Count every terminal including the exposed pad. |
55.6Diodes and thyristors
Diode · LED (diode.led → device led)
Simulation pins: anode, cathode. Curves: Forward voltage vs current, Luminous intensity vs forward current, Relative intensity vs junction temperature, Forward voltage vs junction temperature, Current derating vs ambient temperature.
| Field | Symbol | Unit | Columns | Sets | Where to find it in the datasheet |
|---|---|---|---|---|---|
| Forward voltage * | V_F | V | min, typ, max | Electro-Optical Characteristics table, row "Forward Voltage" (V_F) at I_F = 20 mA (or the stated test current). | |
| Continuous forward current | I_F | A | max | Absolute Maximum Ratings, row "Forward Current" (DC, I_F). | |
| Peak forward current | I_FP | A | max | Absolute Maximum Ratings, row "Peak Forward Current" with its duty cycle and pulse width. | |
| Reverse voltage | V_R | V | max | Absolute Maximum Ratings, row "Reverse Voltage" (often 5 V. LEDs are not meant to block). | |
| Dominant wavelength | λ_d | m | min, typ, max | Electro-Optical Characteristics, row "Dominant Wavelength" (nm, store in metres). | |
| Luminous intensity | I_V | cd | min, typ, max | Electro-Optical Characteristics, row "Luminous Intensity" (mcd) at the test current. | |
| Viewing angle (2θ½) | 2θ½ | deg | typ | Electro-Optical Characteristics, row "Viewing Angle" or the radiation pattern diagram. | |
| Emission coefficient (model) | n | typ | Not in the datasheet: fit two points of the "Forward Current vs Forward Voltage" graph. Leave empty for 1.9. | ||
| Series resistance (model) | R_S | Ohm | typ | Not in the datasheet: slope of the I_F vs V_F graph near the rated current. | |
| Peak wavelength | λ_P | m | typ | Electrical / Optical Characteristics, row "Peak Wavelength" (λ_P). The row above it is usually the dominant wavelength. | |
| Spectral half-width | Δλ | m | typ | Optical Characteristics, row "Spectral Line Half-Width" (Δλ). | |
| Reverse current | I_R | A | max | Electrical Characteristics, row "Reverse Current" at the stated V_R. | |
| Junction capacitance | C_J | F | typ | Electrical Characteristics, row "Capacitance" at V_R = 0 and 1 MHz. | |
| Forward voltage temperature coefficient | ΔV_F/ΔT | V/C | typ | Typical Characteristics, "Forward Voltage vs Temperature" (about -2 to -4 mV/°C). | |
| Thermal resistance, junction to ambient | θ_JA | C/W | typ, max | Thermal Characteristics / Thermal Information table, row "Junction-to-Ambient" (R_θJA). Note the PCB it is quoted on (JEDEC 1s or 2s2p). | |
| Thermal resistance, junction to case | θ_JC | C/W | typ, max | Thermal Characteristics table, row "Junction-to-Case" (R_θJC). For power packages use the tab / bottom value. | |
| Maximum junction temperature | T_J(max) | C | max | Absolute Maximum Ratings table, row "Junction Temperature" or "Operating Junction Temperature" (T_J). | |
| Power dissipation | P_D | W | max | Absolute Maximum Ratings, row "Power Dissipation" (P_D or P_tot) at T_A = 25 °C. If only a derating curve exists read its 25 °C value. | |
| Pin count | N_pins | typ | Package / Pin Configuration drawing on page 1 or 2. Count every terminal including the exposed pad. |
Diode · Rectifier / signal (diode.rectifier → device diode)
Simulation pins: anode, cathode. Symbol variants: rectifier, signal. Curves: Forward voltage vs current, Reverse current vs reverse voltage, Junction capacitance vs reverse voltage, Forward voltage vs junction temperature, Current derating vs temperature.
| Field | Symbol | Unit | Columns | Sets | Where to find it in the datasheet |
|---|---|---|---|---|---|
| Forward voltage * | V_F | V | typ, max | Electrical Characteristics table, row "Forward Voltage" (V_F) at the stated I_F. Put that I_F in the conditions. | |
| Repetitive peak reverse voltage | V_RRM | V | max | Absolute Maximum Ratings, row "Peak Repetitive Reverse Voltage" (V_RRM) or "DC Blocking Voltage" (V_R). | |
| Average forward current | I_F(AV) | A | max | Absolute Maximum Ratings, row "Average Rectified Forward Current" (I_F(AV) or I_O). | |
| Surge forward current | I_FSM | A | max | Absolute Maximum Ratings, row "Non-repetitive Peak Forward Surge Current" (I_FSM, 8.3 ms half sine). | |
| Reverse leakage current | I_R | A | max | Electrical Characteristics, row "Reverse Current" (I_R) at the rated V_R, 25 °C (the 100 °C value is much larger). | |
| Junction capacitance | C_J | F | typ | Electrical Characteristics, row "Junction Capacitance" (C_J or C_T) at V_R = 4 V, 1 MHz, or the C vs V_R graph. | |
| Emission coefficient (model) | n | typ | Not in the datasheet: fit from two points of the "Forward Current vs Forward Voltage" graph (n = ΔV_F / (V_T·ln(I2/I1))). Leave empty for the rectifier default. | ||
| Series resistance (model) | R_S | Ohm | typ | Not in the datasheet: slope of the V_F vs I_F graph at high current (ΔV_F / ΔI_F). | |
| Reverse recovery time | t_rr | s | max | Electrical Characteristics, row "Reverse Recovery Time" (t_rr) with its I_F / I_R / I_rr test conditions. | |
| Forward voltage at low current | V_F | V | typ | Forward-voltage graph or table at a second, lower current (for example 1 mA). With V_F above it, it sets the emission coefficient. | |
| Reverse leakage at high temperature | I_R | A | max | Electrical Characteristics, row "Reverse Current" at T_A or T_J = 100 to 150 °C. | |
| Reverse recovery charge | Q_rr | C | typ | Electrical Characteristics, row "Reverse Recovery Charge". | |
| Repetitive peak forward current | I_FRM | A | max | Absolute Maximum Ratings, row "Repetitive Peak Forward Current". | |
| Forward voltage temperature coefficient | ΔV_F/ΔT | V/C | typ | Typical Characteristics, "Forward Voltage vs Temperature": about -2 mV/°C for silicon junctions (type -2m). | |
| Thermal resistance, junction to ambient | θ_JA | C/W | typ, max | Thermal Characteristics / Thermal Information table, row "Junction-to-Ambient" (R_θJA). Note the PCB it is quoted on (JEDEC 1s or 2s2p). | |
| Thermal resistance, junction to case | θ_JC | C/W | typ, max | Thermal Characteristics table, row "Junction-to-Case" (R_θJC). For power packages use the tab / bottom value. | |
| Maximum junction temperature | T_J(max) | C | max | Absolute Maximum Ratings table, row "Junction Temperature" or "Operating Junction Temperature" (T_J). | |
| Power dissipation | P_D | W | max | Absolute Maximum Ratings, row "Power Dissipation" (P_D or P_tot) at T_A = 25 °C. If only a derating curve exists read its 25 °C value. | |
| Pin count | N_pins | typ | Package / Pin Configuration drawing on page 1 or 2. Count every terminal including the exposed pad. |
Diode · Schottky (diode.schottky → device diode)
Simulation pins: anode, cathode. Symbol variants: schottky. Curves: Forward voltage vs current, Reverse current vs voltage, Junction capacitance vs reverse voltage, Forward voltage vs junction temperature, Reverse current vs junction temperature, Current derating vs temperature.
| Field | Symbol | Unit | Columns | Sets | Where to find it in the datasheet |
|---|---|---|---|---|---|
| Forward voltage * | V_F | V | typ, max | Electrical Characteristics table, row "Forward Voltage" (V_F) at the stated I_F. Put that I_F in the conditions. | |
| Repetitive peak reverse voltage | V_RRM | V | max | Absolute Maximum Ratings, row "Peak Repetitive Reverse Voltage" (V_RRM) or "DC Blocking Voltage" (V_R). | |
| Average forward current | I_F(AV) | A | max | Absolute Maximum Ratings, row "Average Rectified Forward Current" (I_F(AV) or I_O). | |
| Surge forward current | I_FSM | A | max | Absolute Maximum Ratings, row "Non-repetitive Peak Forward Surge Current" (I_FSM, 8.3 ms half sine). | |
| Reverse leakage current | I_R | A | max | Electrical Characteristics, row "Reverse Current" (I_R) at the rated V_R, 25 °C (the 100 °C value is much larger). | |
| Junction capacitance | C_J | F | typ | Electrical Characteristics, row "Junction Capacitance" (C_J or C_T) at V_R = 4 V, 1 MHz, or the C vs V_R graph. | |
| Emission coefficient (model) | n | typ | Not in the datasheet: fit from two points of the "Forward Current vs Forward Voltage" graph (n = ΔV_F / (V_T·ln(I2/I1))). Leave empty for the Schottky default. | ||
| Series resistance (model) | R_S | Ohm | typ | Not in the datasheet: slope of the V_F vs I_F graph at high current (ΔV_F / ΔI_F). | |
| Forward voltage at low current | V_F | V | typ | Forward-voltage graph or table at a second, lower current (for example 1 mA). | |
| Reverse leakage at high temperature | I_R | A | max | Electrical Characteristics, row "Reverse Current" at T_J = 100 to 125 °C. Schottky leakage grows by orders of magnitude with temperature. | |
| Total capacitive charge | Q_c | C | typ | Electrical Characteristics, row "Total Capacitive Charge" (Q_c), the Schottky counterpart of reverse recovery charge. | |
| Repetitive peak forward current | I_FRM | A | max | Absolute Maximum Ratings, row "Repetitive Peak Forward Current". | |
| Forward voltage temperature coefficient | ΔV_F/ΔT | V/C | typ | Typical Characteristics, "Forward Voltage vs Temperature" (about -1 to -2 mV/°C). | |
| Thermal resistance, junction to ambient | θ_JA | C/W | typ, max | Thermal Characteristics / Thermal Information table, row "Junction-to-Ambient" (R_θJA). Note the PCB it is quoted on (JEDEC 1s or 2s2p). | |
| Thermal resistance, junction to case | θ_JC | C/W | typ, max | Thermal Characteristics table, row "Junction-to-Case" (R_θJC). For power packages use the tab / bottom value. | |
| Maximum junction temperature | T_J(max) | C | max | Absolute Maximum Ratings table, row "Junction Temperature" or "Operating Junction Temperature" (T_J). | |
| Power dissipation | P_D | W | max | Absolute Maximum Ratings, row "Power Dissipation" (P_D or P_tot) at T_A = 25 °C. If only a derating curve exists read its 25 °C value. | |
| Pin count | N_pins | typ | Package / Pin Configuration drawing on page 1 or 2. Count every terminal including the exposed pad. |
Diode · TVS (diode.tvs → device diode)
Simulation pins: anode, cathode. Symbol variants: tvs. Curves: Clamping voltage vs peak pulse current, Peak pulse power vs pulse width, Capacitance vs reverse voltage.
| Field | Symbol | Unit | Columns | Sets | Where to find it in the datasheet |
|---|---|---|---|---|---|
| Reverse stand-off voltage | V_RWM | V | max | Electrical Characteristics table, column "Reverse Stand-off Voltage" (V_RWM or V_R): the highest normal working voltage. | |
| Breakdown voltage * | V_BR | V | min, typ, max | Electrical Characteristics table, column "Breakdown Voltage" V_BR min / max at the test current I_T (1 mA or 10 mA). | |
| Clamping voltage * | V_C | V | max | Electrical Characteristics table, column "Maximum Clamping Voltage" V_C at I_PP (8/20 µs or 10/1000 µs pulse, say which). | |
| Peak pulse current * | I_PP | A | max | Electrical Characteristics table, column "Peak Pulse Current" I_PP for the same pulse shape as V_C. | |
| Peak pulse power | P_PP | W | max | Absolute Maximum Ratings, row "Peak Pulse Power Dissipation" (P_PPM) for the 10/1000 µs waveform. | |
| Reverse leakage current | I_R | A | max | Electrical Characteristics table, column "I_R" at V_RWM. | |
| Junction capacitance | C_J | F | typ | Electrical Characteristics, row "Capacitance" at 0 V or V_RWM, 1 MHz (matters for data lines). | |
| Breakdown test current | I_T | A | typ | Electrical Characteristics: the current V_BR is measured at (I_T), typically 1 or 10 mA. | |
| Breakdown voltage temperature coefficient | α_VBR | %/C | typ | Electrical Characteristics, row "Temperature Coefficient of V_BR" (about 0.1 %/°C). | |
| Response time | t_resp | s | typ | Features or Electrical Characteristics, row "Response Time" (a few ps to ns for the junction itself). | |
| Bidirectional (1 = yes) | bi | typ | Part number suffix: "CA" or "C" means bidirectional, "A" unidirectional. | ||
| Thermal resistance, junction to ambient | θ_JA | C/W | typ, max | Thermal Characteristics / Thermal Information table, row "Junction-to-Ambient" (R_θJA). Note the PCB it is quoted on (JEDEC 1s or 2s2p). | |
| Thermal resistance, junction to case | θ_JC | C/W | typ, max | Thermal Characteristics table, row "Junction-to-Case" (R_θJC). For power packages use the tab / bottom value. | |
| Maximum junction temperature | T_J(max) | C | max | Absolute Maximum Ratings table, row "Junction Temperature" or "Operating Junction Temperature" (T_J). | |
| Power dissipation | P_D | W | max | Absolute Maximum Ratings, row "Power Dissipation" (P_D or P_tot) at T_A = 25 °C. If only a derating curve exists read its 25 °C value. | |
| Pin count | N_pins | typ | Package / Pin Configuration drawing on page 1 or 2. Count every terminal including the exposed pad. |
Diode · Zener (diode.zener → device diode)
Simulation pins: anode, cathode. Symbol variants: zener. Curves: Zener current vs voltage, Dynamic impedance vs zener current, Zener voltage vs junction temperature, Capacitance vs reverse voltage.
| Field | Symbol | Unit | Columns | Sets | Where to find it in the datasheet |
|---|---|---|---|---|---|
| Zener voltage * | V_Z | V | min, typ, max | Electrical Characteristics table, row for your part number, columns V_Z min / nom / max at the test current I_ZT. | |
| Dynamic impedance at I_ZT | Z_ZT | Ohm | max | Electrical Characteristics table, column "Z_ZT" (or r_dif) at I_ZT. | |
| Dynamic impedance at the knee | Z_ZK | Ohm | max | Electrical Characteristics table, column "Z_ZK" at I_ZK (a small current, for example 0.25 mA). | |
| Reverse leakage current | I_R | A | max | Electrical Characteristics table, column "I_R" at the stated V_R below V_Z. | |
| Forward voltage | V_F | V | max | Electrical Characteristics header or footnote: "V_F = 0.9 V max at I_F = 10 mA". | |
| Temperature coefficient of V_Z | S_Z | V/C | typ | Electrical Characteristics table, column "Temperature Coefficient" (mV/K). Store in V/°C. | |
| Maximum zener current | I_ZM | A | max | Usually not listed: I_ZM = P_D / V_Z(max) from the Power Dissipation rating. | |
| Test current | I_ZT | A | typ | Electrical Characteristics: the test current V_Z is quoted at (I_ZT). Put the same value in the V_Z condition. | |
| Knee current | I_ZK | A | typ | Electrical Characteristics, row "Knee Impedance" (Z_ZK) names the knee current I_ZK. | |
| Non-repetitive surge current | I_ZSM | A | max | Absolute Maximum Ratings or the surge table, row "Non-Repetitive Peak Reverse Current". | |
| Junction capacitance | C_J | F | typ | Electrical Characteristics, row "Total Capacitance" (C_T) at the stated V_R and 1 MHz. | |
| Thermal resistance, junction to ambient | θ_JA | C/W | typ, max | Thermal Characteristics / Thermal Information table, row "Junction-to-Ambient" (R_θJA). Note the PCB it is quoted on (JEDEC 1s or 2s2p). | |
| Thermal resistance, junction to case | θ_JC | C/W | typ, max | Thermal Characteristics table, row "Junction-to-Case" (R_θJC). For power packages use the tab / bottom value. | |
| Maximum junction temperature | T_J(max) | C | max | Absolute Maximum Ratings table, row "Junction Temperature" or "Operating Junction Temperature" (T_J). | |
| Power dissipation | P_D | W | max | Absolute Maximum Ratings, row "Power Dissipation" (P_D or P_tot) at T_A = 25 °C. If only a derating curve exists read its 25 °C value. | |
| Pin count | N_pins | typ | Package / Pin Configuration drawing on page 1 or 2. Count every terminal including the exposed pad. |
Diodes · Bridge rectifier (diodes.bridge → device bridge)
Simulation pins: ac1, ac2, +, −.
| Field | Symbol | Unit | Columns | Sets | Where to find it in the datasheet |
|---|---|---|---|---|---|
| Forward voltage per element * | V_F | V | max | vf | Electrical characteristics, "Forward voltage drop per element" at I_F. |
| VF test current | I_F | A | typ | if_test | Condition of the V_F row. |
| Average rectified current | I_O | A | max | irated | Maximum ratings, "Average rectified output current". |
| Repetitive reverse voltage | V_RRM | V | max | bv | Maximum ratings, "V_RRM". |
| Surge current | I_FSM | A | max | Maximum ratings, "Peak forward surge current" (informational). | |
| Operating temperature range | T_op | C | min, max | Features or Recommended Operating Conditions, row "Operating Temperature Range" (minimum and maximum). | |
| Pin count | N_pins | typ | Package / Pin Configuration drawing on page 1 or 2. Count every terminal including the exposed pad. |
Diodes · Current-regulating diode (diodes.crd → device crd)
Simulation pins: anode, cathode.
| Field | Symbol | Unit | Columns | Sets | Where to find it in the datasheet |
|---|---|---|---|---|---|
| Regulated current * | I_P | A | min, typ, max | ip | Electrical characteristics, "Pinch-off current I_P" at V_T. |
| Knee (limiting) voltage | V_K | V | max | vk | Row "Limiting voltage V_L" / "knee voltage". |
| Peak operating voltage | POV | V | max | vmax | Absolute maximum, "Peak operating voltage". |
| Operating temperature range | T_op | C | min, max | Features or Recommended Operating Conditions, row "Operating Temperature Range" (minimum and maximum). | |
| Pin count | N_pins | typ | Package / Pin Configuration drawing on page 1 or 2. Count every terminal including the exposed pad. |
Diodes · DIAC / SIDAC / TSS (diodes.diac → device diac)
Simulation pins: a, b. Symbol variants: diac, sidac, tss.
| Field | Symbol | Unit | Columns | Sets | Where to find it in the datasheet |
|---|---|---|---|---|---|
| Breakover voltage * | V_BO | V | min, typ, max | vbo | Electrical characteristics, row "Breakover voltage V_BO". |
| Breakover voltage symmetry / fold-back | ΔV | V | typ | dv | Row "Dynamic breakover voltage ΔV" (DIAC). |
| Holding current | I_H | A | typ | ih | Row "Holding current" (SIDAC / TSS). |
| Operating temperature range | T_op | C | min, max | Features or Recommended Operating Conditions, row "Operating Temperature Range" (minimum and maximum). | |
| Pin count | N_pins | typ | Package / Pin Configuration drawing on page 1 or 2. Count every terminal including the exposed pad. |
Diodes · Dual diode (diodes.diode2 → device diode2)
Simulation pins: a1, a2, k. Symbol variants: cc, ca, series, dual.
| Field | Symbol | Unit | Columns | Sets | Where to find it in the datasheet |
|---|---|---|---|---|---|
| Forward voltage * | V_F | V | max | Electrical characteristics, "Forward voltage" at I_F (per diode). | |
| VF test current | I_F | A | typ | Condition of the V_F row. | |
| Reverse voltage | V_R | V | max | bv | Maximum ratings, "V_RRM" / "V_R". |
| Reverse recovery time | t_rr | s | max | tt | Row "t_rr". |
| Junction capacitance | C_J | F | max | cj0 | Row "C_T / C_D" at V_R. |
| Operating temperature range | T_op | C | min, max | Features or Recommended Operating Conditions, row "Operating Temperature Range" (minimum and maximum). | |
| Pin count | N_pins | typ | Package / Pin Configuration drawing on page 1 or 2. Count every terminal including the exposed pad. |
Diodes · SCR (diodes.scr → device scr)
Simulation pins: anode, cathode, gate.
| Field | Symbol | Unit | Columns | Sets | Where to find it in the datasheet |
|---|---|---|---|---|---|
| Gate trigger current * | I_GT | A | max | igt | Electrical characteristics, row "Gate trigger current I_GT" (max). |
| Gate trigger voltage | V_GT | V | max | vgt | Row "Gate trigger voltage V_GT". |
| Holding current | I_H | A | max | ih | Row "Holding current I_H". |
| On-state voltage | V_TM | V | max | vtm | Row "On-state voltage V_TM" at I_TM. |
| Repetitive off-state voltage | V_DRM | V | max | vdrm | Absolute maximum, "V_DRM / V_RRM". |
| RMS on-state current | I_T(RMS) | A | max | Absolute maximum, "I_T(RMS)" (informational). | |
| Operating temperature range | T_op | C | min, max | Features or Recommended Operating Conditions, row "Operating Temperature Range" (minimum and maximum). | |
| Pin count | N_pins | typ | Package / Pin Configuration drawing on page 1 or 2. Count every terminal including the exposed pad. |
Diodes · TRIAC (diodes.triac → device triac)
Simulation pins: mt1, mt2, gate.
| Field | Symbol | Unit | Columns | Sets | Where to find it in the datasheet |
|---|---|---|---|---|---|
| Gate trigger current * | I_GT | A | max | igt | Electrical characteristics, "I_GT" per quadrant. Use the largest of Q1–Q3. |
| Holding current | I_H | A | max | ih | Row "Holding current I_H". |
| On-state voltage | V_TM | V | max | vtm | Row "V_TM" at I_TM. |
| Repetitive off-state voltage | V_DRM | V | max | vdrm | Absolute maximum, "V_DRM". |
| RMS on-state current | I_T(RMS) | A | max | Absolute maximum, "I_T(RMS)" (informational). | |
| Operating temperature range | T_op | C | min, max | Features or Recommended Operating Conditions, row "Operating Temperature Range" (minimum and maximum). | |
| Pin count | N_pins | typ | Package / Pin Configuration drawing on page 1 or 2. Count every terminal including the exposed pad. |
55.7Displays
Displays · 4-digit 7-segment display (displays.seg7x4 → device seg7x4)
Simulation pins: a, b, c, d, e, f, g, dp, d1, d2, d3, d4. Symbol variants: cc, ca.
| Field | Symbol | Unit | Columns | Sets | Where to find it in the datasheet |
|---|---|---|---|---|---|
| Forward voltage * | V_F | V | typ, max | vf | Electro-optical characteristics, "Forward voltage" at I_F (per colour / segment). |
| Test current | I_F | A | typ | if_test | Condition of the V_F row (10 mA / 20 mA). |
| Max forward current | I_F(max) | A | max | Absolute maximum, "Forward current" (W_RATING). | |
| Common anode / cathode * | CA/CC | typ | Internal circuit drawing → variant. | ||
| Operating temperature range | T_op | C | min, max | Features or Recommended Operating Conditions, row "Operating Temperature Range" (minimum and maximum). | |
| Pin count | N_pins | typ | Package / Pin Configuration drawing on page 1 or 2. Count every terminal including the exposed pad. |
Displays · 7-segment display (displays.seg7 → device seg7)
Simulation pins: a, b, c, d, e, f, g, dp, com. Symbol variants: cc, ca.
| Field | Symbol | Unit | Columns | Sets | Where to find it in the datasheet |
|---|---|---|---|---|---|
| Forward voltage * | V_F | V | typ, max | vf | Electro-optical characteristics, "Forward voltage" at I_F (per colour / segment). |
| Test current | I_F | A | typ | if_test | Condition of the V_F row (10 mA / 20 mA). |
| Max forward current | I_F(max) | A | max | Absolute maximum, "Forward current" (W_RATING). | |
| Common anode / cathode * | CA/CC | typ | Part number / internal circuit drawing (…AS = cathode, …BS = anode for 5161) → variant. | ||
| Operating temperature range | T_op | C | min, max | Features or Recommended Operating Conditions, row "Operating Temperature Range" (minimum and maximum). | |
| Pin count | N_pins | typ | Package / Pin Configuration drawing on page 1 or 2. Count every terminal including the exposed pad. |
Displays · Display module (displays.display → device display)
Simulation pins: VSS, VDD, V0, RS, RW, E, D0, D1, D2, D3, D4, D5, D6, D7, A, K. Symbol variants: hd44780, oled_i2c, oled_spi, tft_spi, epaper.
| Field | Symbol | Unit | Columns | Sets | Where to find it in the datasheet |
|---|---|---|---|---|---|
| Supply current * | I_DD | A | typ, max | idd | Electrical characteristics, "Supply current" (logic, backlight off). |
| Backlight forward voltage | V_F(BL) | V | typ | vf_bl | Backlight characteristics, "Forward voltage" (LED A–K). |
| Backlight current | I_F(BL) | A | typ | Backlight characteristics, "Forward current". | |
| Operating temperature range | T_op | C | min, max | Features or Recommended Operating Conditions, row "Operating Temperature Range" (minimum and maximum). | |
| Pin count | N_pins | typ | Package / Pin Configuration drawing on page 1 or 2. Count every terminal including the exposed pad. |
Displays · LED matrix (displays.ledmatrix → device ledmatrix)
Simulation pins: r1, r2, r3, r4, r5, r6, r7, r8, c1, c2, c3, c4, c5, c6, c7, c8. Symbol variants: row_anode, row_cathode.
| Field | Symbol | Unit | Columns | Sets | Where to find it in the datasheet |
|---|---|---|---|---|---|
| Forward voltage * | V_F | V | typ, max | vf | Electro-optical characteristics, "Forward voltage" at I_F (per colour / segment). |
| Test current | I_F | A | typ | if_test | Condition of the V_F row (10 mA / 20 mA). |
| Max forward current | I_F(max) | A | max | Absolute maximum, "Forward current" (W_RATING). | |
| Operating temperature range | T_op | C | min, max | Features or Recommended Operating Conditions, row "Operating Temperature Range" (minimum and maximum). | |
| Pin count | N_pins | typ | Package / Pin Configuration drawing on page 1 or 2. Count every terminal including the exposed pad. |
55.8Electromechanical
Electromechanical · Latching relay (electromech.relay_latch → device relay_latch)
Simulation pins: coil+, coil−, com, no, nc. Symbol variants: single_coil, single_coil_2p, dual_coil, dual_coil_2p.
| Field | Symbol | Unit | Columns | Sets | Where to find it in the datasheet |
|---|---|---|---|---|---|
| Nominal coil voltage * | V_coil | V | typ | vcoil | Coil Data table, column "Nominal Voltage" (or "Rated Voltage") for your coil code. |
| Coil resistance * | R_coil | Ohm | typ | rcoil | Coil Data table, column "Coil Resistance" (±10 %). Or nominal power P → R = V²/P. |
| Set / reset voltage | V_set | V | max | vpick | Coil Data table, column "Set Voltage" / "Must Set" (max). |
| Set time | t_set | s | typ, max | t_op | Characteristics table, row "Set Time" (or Operate Time). |
| Minimum pulse width | t_pulse | s | min | pulse_min | Coil Data notes: "Minimum pulse width" / "recommended set pulse" (often 10 ms or 3 × set time). |
| Contact resistance | R_contact | Ohm | max | ron | Contact Data, row "Contact Resistance". |
| Rated contact current | I_contact | A | max | imax | Contact Data, row "Rated Load". |
| Operating temperature range | T_op | C | min, max | Features or Recommended Operating Conditions, row "Operating Temperature Range" (minimum and maximum). | |
| Pin count | N_pins | typ | Package / Pin Configuration drawing on page 1 or 2. Count every terminal including the exposed pad. |
Electromechanical · Relay (electromech.relay → device relay)
Simulation pins: coil+, coil−, com, no, nc. Symbol variants: spdt, spst_no, spst_nc, dpst_no, dpdt, 4pdt, reed.
| Field | Symbol | Unit | Columns | Sets | Where to find it in the datasheet |
|---|---|---|---|---|---|
| Nominal coil voltage * | V_coil | V | typ | vcoil | Coil Data table, column "Nominal Voltage" (or "Rated Voltage") for your coil code. |
| Coil resistance * | R_coil | Ohm | typ | rcoil | Coil Data table, column "Coil Resistance" (±10 %). Or nominal power P → R = V²/P. |
| Must-operate voltage | V_op | V | max | vpick | Coil Data table, column "Must Operate" / "Pick-up Voltage" (max, typically 75 % of nominal). |
| Must-release voltage | V_rel | V | min | vdrop | Coil Data table, column "Must Release" / "Drop-out Voltage" (min, typically 10 % of nominal). |
| Operate time | t_op | s | typ, max | t_op | Characteristics table, row "Operate Time" at nominal voltage, without bounce. |
| Release time | t_rel | s | typ, max | t_rel | Characteristics table, row "Release Time" (without coil diode). |
| Contact resistance | R_contact | Ohm | max | ron | Contact Data, row "Initial Contact Resistance" (max, for example 100 mΩ at 6 V 1 A). |
| Rated contact current | I_contact | A | max | imax | Contact Data, row "Rated Load" / "Max Switching Current". |
| Max switching voltage | V_contact | V | max | vmax | Contact Data, row "Max Switching Voltage". |
| Contact bounce time | t_bounce | s | max | bounce | Characteristics table, row "Bounce Time" (often in the operate-time footnote). |
| Built-in coil diode | D_coil | 0/1 | typ | diode | Ordering code / schematic on page 1: "with diode" (often suffix D) → 1. |
| Coil power | P_c | W | typ | Specifications, row "Coil Power" (nominal). | |
| Maximum switching current | I_sw | A | max | Contact data, row "Switching Current (max)". | |
| Mechanical life | N_mech | min | Specifications, row "Mechanical Life" (operations). | ||
| Electrical life | N_elec | min | Specifications, row "Electrical Life" at the stated load (operations). | ||
| Operating temperature range | T_op | C | min, max | Features or Recommended Operating Conditions, row "Operating Temperature Range" (minimum and maximum). | |
| Pin count | N_pins | typ | Package / Pin Configuration drawing on page 1 or 2. Count every terminal including the exposed pad. |
Electromechanical · Rotary encoder (electromech.encoder → device encoder)
Simulation pins: A, C, B. Symbol variants: 3pin, 5pin.
| Field | Symbol | Unit | Columns | Sets | Where to find it in the datasheet |
|---|---|---|---|---|---|
| Pulses per revolution * | PPR | typ | ppr | Specifications: "Resolution" / "Pulses / 360°" (per channel). | |
| Detents | N_det | typ | detents | Specifications: "Detent" / "Click" count per revolution. | |
| Contact resistance | R_contact | Ohm | max | ron | Electrical: "Contact Resistance" (max). |
| Chattering / bounce | t_bounce | s | max | bounce | Electrical: "Chattering" or "Bounce" (ms at a given speed). |
| Operating temperature range | T_op | C | min, max | Features or Recommended Operating Conditions, row "Operating Temperature Range" (minimum and maximum). | |
| Pin count | N_pins | typ | Package / Pin Configuration drawing on page 1 or 2. Count every terminal including the exposed pad. |
Electromechanical · Solid-state relay (electromech.ssr → device ssr)
Simulation pins: in+, in−, out1, out2. Symbol variants: dc, ac, photomos.
| Field | Symbol | Unit | Columns | Sets | Where to find it in the datasheet |
|---|---|---|---|---|---|
| LED operate current * | I_F(on) | A | max | if_on | Input characteristics, row "LED Operate Current" / "Trigger current" (max). |
| Input forward voltage | V_F | V | typ | vf | Input characteristics, row "LED Forward Voltage" at I_F = 10 mA. |
| On resistance | R_on | Ohm | typ, max | ron | Output characteristics, row "On-state Resistance" (DC / PhotoMOS). |
| On-state voltage (AC) | V_TM | V | typ, max | vtm | Output characteristics, row "On-state Voltage Drop" (triac SSR). |
| Load current | I_L | A | max | imax | Output ratings, row "Load Current". |
| Turn-on time | t_on | s | max | t_on | Switching characteristics, row "Turn-on Time". |
| Turn-off time | t_off | s | max | t_off | Switching characteristics, row "Turn-off Time". |
| Holding current (AC) | I_H | A | max | ih | Output characteristics, row "Holding Current". |
| Operating temperature range | T_op | C | min, max | Features or Recommended Operating Conditions, row "Operating Temperature Range" (minimum and maximum). | |
| Pin count | N_pins | typ | Package / Pin Configuration drawing on page 1 or 2. Count every terminal including the exposed pad. |
Electromechanical · Switch (electromech.sw → device sw)
Simulation pins: com, a. Symbol variants: spst, spdt, dpst, dpdt, push_no, push_nc, tact4, toggle, slide, micro, reed, dip1, dip2, dip3, dip4, dip5, dip6, dip8, dip10, rotary.
| Field | Symbol | Unit | Columns | Sets | Where to find it in the datasheet |
|---|---|---|---|---|---|
| Contact resistance | R_contact | Ohm | max | ron | Electrical specifications, row "Contact Resistance" (max, initial). |
| Contact rating, current | I_rating | A | max | imax | Electrical specifications, row "Rating" (for example 50 mA 12 VDC). |
| Contact rating, voltage | V_rating | V | max | Electrical specifications, row "Rating" (voltage part). | |
| Bounce time | t_bounce | s | max | bounce | Electrical specifications, row "Bounce Time" (tactile switches: ≤ 5 ms typical). |
| Operating temperature range | T_op | C | min, max | Features or Recommended Operating Conditions, row "Operating Temperature Range" (minimum and maximum). | |
| Positions | N_pos | typ | positions | Mechanical specifications: number of positions (rotary / selector switches). | |
| Electrical life | N_ops | cycles | min | Life / Durability row (informational). | |
| Pin count | N_pins | typ | Package / Pin Configuration drawing on page 1 or 2. Count every terminal including the exposed pad. |
55.9Interface
Interface · Analog switch / multiplexer (interface.amux → device amux)
Simulation pins: Y0, Y1, Y2, Y3, Y4, Y5, Y6, Y7, Z, S0, S1, S2, EN, VDD, VSS, VEE. Symbol variants: 1x8, 1x4, 1x16, 2x4, 3x2, spst_quad, spst, spdt, dual_spdt.
| Field | Symbol | Unit | Columns | Sets | Where to find it in the datasheet |
|---|---|---|---|---|---|
| On resistance * | R_ON | Ohm | typ, max | ron | Electrical Characteristics, row "ON Resistance" (R_ON) at the supply you use. Read the typ / max at V_IS = mid supply. |
| Supply for R_ON | V_DD(R_ON) | V | typ | ron_vdd | Condition column of the R_ON row (V_CC / V_DD). |
| R_ON flatness | R_FLAT | Ohm | typ, max | ron_flat | Row "ON-resistance flatness" (ΔR_ON over the signal range). Converted to the relative ron_flat. |
| Turn-on / switching time | t_ON | s | typ, max | tsw | Switching Characteristics, row "t_ON" / "Propagation delay, select to output". |
| Charge injection | Q_INJ | C | typ | qinj | Row "Charge Injection" (pC). |
| Off capacitance (channel) | C_S(OFF) | F | typ | cs | Row "Source OFF capacitance" / "C_IS". |
| Supply range | V_DD | V | min, max | Recommended Operating Conditions, row "Supply Voltage". | |
| Operating temperature range | T_op | C | min, max | Features or Recommended Operating Conditions, row "Operating Temperature Range" (minimum and maximum). | |
| Pin count | N_pins | typ | Package / Pin Configuration drawing on page 1 or 2. Count every terminal including the exposed pad. |
Interface · CAN transceiver (interface.can → device can)
Simulation pins: TXD, GND, VCC, RXD, VREF, CANL, CANH, S. Symbol variants: 5v, 3v3.
| Field | Symbol | Unit | Columns | Sets | Where to find it in the datasheet |
|---|---|---|---|---|---|
| Dominant differential voltage | V_OD(D) | V | min, typ, max | v_dom | Driver characteristics, "Differential output voltage, dominant". |
| Receiver threshold | V_TH | V | min, typ, max | vth | Receiver, "Differential input threshold". |
| Loop delay | t_LOOP | s | max | tpd | "Loop delay TXD to RXD". |
| Operating temperature range | T_op | C | min, max | Features or Recommended Operating Conditions, row "Operating Temperature Range" (minimum and maximum). | |
| Pin count | N_pins | typ | Package / Pin Configuration drawing on page 1 or 2. Count every terminal including the exposed pad. |
Interface · Digital isolator (interface.isolator → device isolator)
Simulation pins: VCC1, INA, INB, GND1, GND2, OUTB, OUTA, VCC2. Symbol variants: 2ch, 4ch, i2c.
| Field | Symbol | Unit | Columns | Sets | Where to find it in the datasheet |
|---|---|---|---|---|---|
| Propagation delay | t_PD | s | typ, max | tpd | Switching characteristics, "Propagation delay". |
| Supply current per side | I_CC | A | typ, max | icc | "Supply current" (side 1 / side 2, DC). |
| Isolation rating | V_ISO | V | min | "Isolation voltage" (informational). | |
| Common-mode transient immunity | CMTI | V/s | min | Electrical Characteristics, row "CMTI" (kV/µs: 50 kV/µs is 5e10 V/s). | |
| Maximum data rate | DR | Hz | min | Switching Characteristics, row "Data Rate" (Mbps counts as MHz here). | |
| Pulse width distortion | PWD | s | max | Switching Characteristics, row "Pulse Width Distortion". | |
| Channel-to-channel skew | t_sk | s | max | Switching Characteristics, row "Channel-to-Channel Output Skew". | |
| Operating temperature range | T_op | C | min, max | Features or Recommended Operating Conditions, row "Operating Temperature Range" (minimum and maximum). | |
| Pin count | N_pins | typ | Package / Pin Configuration drawing on page 1 or 2. Count every terminal including the exposed pad. |
Interface · Integrated circuit (interface.chip → device chip)
Simulation pins: 1, 2, 3, 4. Symbol variants: generic, eeprom, spi_flash, i2c_dev, spi_dev, usb_uart, rtc.
| Field | Symbol | Unit | Columns | Sets | Where to find it in the datasheet |
|---|---|---|---|---|---|
| Supply current | I_DD | A | typ, max | idd | Electrical characteristics, "Supply / operating current" in your mode. |
| Supply range | V_DD | V | min, max | Recommended operating conditions. | |
| Operating temperature range | T_op | C | min, max | Features or Recommended Operating Conditions, row "Operating Temperature Range" (minimum and maximum). | |
| Pin count | N_pins | typ | Package / Pin Configuration drawing on page 1 or 2. Count every terminal including the exposed pad. |
Interface · RS-232 transceiver (interface.rs232 → device rs232)
Simulation pins: C1+, V+, C1−, C2+, C2−, V−, T2OUT, R2IN, R2OUT, T2IN, T1IN, R1OUT, R1IN, T1OUT, GND, VCC. Symbol variants: max232, max3232.
| Field | Symbol | Unit | Columns | Sets | Where to find it in the datasheet |
|---|---|---|---|---|---|
| Driver output swing | V_O | V | min | v_pump | Driver characteristics, "Output voltage swing" (±). |
| Receiver threshold | V_TH | V | typ | vth | Receiver, "Input threshold low / high". |
| Operating temperature range | T_op | C | min, max | Features or Recommended Operating Conditions, row "Operating Temperature Range" (minimum and maximum). | |
| Pin count | N_pins | typ | Package / Pin Configuration drawing on page 1 or 2. Count every terminal including the exposed pad. |
Interface · RS-485 transceiver (interface.rs485 → device rs485)
Simulation pins: RO, nRE, DE, DI, GND, A, B, VCC.
| Field | Symbol | Unit | Columns | Sets | Where to find it in the datasheet |
|---|---|---|---|---|---|
| Differential output voltage | V_OD | V | min, typ | vod | Driver characteristics, "Differential output voltage" with R_L = 54 Ω. |
| Receiver threshold | V_TH | V | min, max | vth | Receiver characteristics, "Differential input threshold". |
| Receiver input resistance | R_IN | Ohm | min | rin | "Receiver input resistance" (12 kΩ = 1 unit load). |
| Propagation delay | t_PD | s | typ, max | tpd | "Driver / receiver propagation delay". |
| Operating temperature range | T_op | C | min, max | Features or Recommended Operating Conditions, row "Operating Temperature Range" (minimum and maximum). | |
| Pin count | N_pins | typ | Package / Pin Configuration drawing on page 1 or 2. Count every terminal including the exposed pad. |
55.10Logic and digital
Digital · Microcontroller (ctrl block) (digital.mcu → device ctrl)
Simulation pins: ain, out, gnd.
| Field | Symbol | Unit | Columns | Sets | Where to find it in the datasheet |
|---|---|---|---|---|---|
| Supply / output high voltage * | V_DD | V | min, typ, max | Recommended Operating Conditions, row "Supply Voltage" (V_DD). Outputs swing to this level (vhi in the ctrl block). | |
| ADC resolution * | N | bit | typ | ADC Characteristics table, row "Resolution" (bits). Use the effective value if you will oversample. | |
| Sample / control-loop rate * | f_S | Hz | max | ADC Characteristics, row "Sampling Rate" or "Conversion Time" (f_S = 1 / t_CONV). The ctrl block runs step() at this rate. | |
| ADC reference voltage * | V_REF | V | min, typ, max | ADC Characteristics, row "Reference Voltage" (V_REF+, internal reference or V_DDA): full-scale input. | |
| ADC input channels | n_ch | typ | Pinout / ADC overview: number of analog input channels. | ||
| ADC integral non-linearity | INL | LSB | typ, max | ADC Characteristics, row "Integral Linearity Error" (±LSB). | |
| ADC input impedance (sampling) | R_AIN | Ohm | min | ADC Characteristics, rows "R_AIN" / "C_ADC" (or the max source impedance table). The ctrl block models 1 MΩ. | |
| Output drive current | I_OH / I_OL | A | max | I/O Port Characteristics, rows I_OH / I_OL at the V_OH / V_OL limits. | |
| Output resistance | R_OUT | Ohm | typ | Not listed directly: R_OUT ≈ (V_DD − V_OH) / I_OH from the I/O Port Characteristics table. | |
| PWM resolution | N_PWM | bit | typ | Timer / PWM chapter: counter width (16-bit timer) or the high-resolution PWM step. | |
| Timer clock | f_TIM | Hz | max | Clock tree / Timer characteristics: timer input clock. PWM resolution = log2(f_TIM / f_PWM). | |
| Output edge time | t_r | s | typ, max | I/O AC Characteristics, rows t_r / t_f at the selected speed setting and load. | |
| Thermal resistance, junction to ambient | θ_JA | C/W | typ, max | Thermal Characteristics / Thermal Information table, row "Junction-to-Ambient" (R_θJA). Note the PCB it is quoted on (JEDEC 1s or 2s2p). | |
| Thermal resistance, junction to case | θ_JC | C/W | typ, max | Thermal Characteristics table, row "Junction-to-Case" (R_θJC). For power packages use the tab / bottom value. | |
| Maximum junction temperature | T_J(max) | C | max | Absolute Maximum Ratings table, row "Junction Temperature" or "Operating Junction Temperature" (T_J). | |
| Power dissipation | P_D | W | max | Absolute Maximum Ratings, row "Power Dissipation" (P_D or P_tot) at T_A = 25 °C. If only a derating curve exists read its 25 °C value. | |
| Pin count | N_pins | typ | Package / Pin Configuration drawing on page 1 or 2. Count every terminal including the exposed pad. |
Logic · 74xx / 4000 IC (logic.logic → device logic)
Simulation pins: 1A, 1Y, 2A, 2Y, 3A, 3Y, GND, 4Y, 4A, 5Y, 5A, 6Y, 6A, VCC. Symbol variants: 14, 32, 74, 86, 123, 125, 138, 151, 157, 161, 164, 165, 244, 245, 573, 574, 595, 4017, 4040, 4060, 4511, 00, 08, 02, 04, 1g00, 1g08, 1g32, 1g86, 1g04, 1g14, 1g125.
| Field | Symbol | Unit | Columns | Sets | Where to find it in the datasheet |
|---|---|---|---|---|---|
| Logic family * | family | typ | family | Part-number letters: HC, HCT, AHC, LVC, LS, CD4000 → family (sets thresholds, drive, tpd). | |
| Supply voltage | V_CC | V | min, typ, max | vcc | Recommended operating conditions, "Supply voltage". |
| Propagation delay | t_PD | s | typ, max | tpd | Switching characteristics, "t_PLH / t_PHL" at your V_CC and C_L. |
| Output drive current | I_OH / I_OL | A | typ | "High / low-level output current" (fits rout_h / rout_l). | |
| Quiescent current | I_CC | A | max | "Quiescent supply current". | |
| Operating temperature range | T_op | C | min, max | Features or Recommended Operating Conditions, row "Operating Temperature Range" (minimum and maximum). | |
| Pin count | N_pins | typ | Package / Pin Configuration drawing on page 1 or 2. Count every terminal including the exposed pad. |
Logic · Gate (logic.gate → device nand)
Simulation pins: in1, in2, out.
| Field | Symbol | Unit | Columns | Sets | Where to find it in the datasheet |
|---|---|---|---|---|---|
| Supply voltage * | V_CC | V | min, typ, max | Recommended Operating Conditions, row "Supply Voltage" (V_CC). The live model uses typ as the logic high level. | |
| Propagation delay * | t_PD | s | typ, max | Switching Characteristics, rows t_PLH / t_PHL at your V_CC and C_L = 15 or 50 pF. Use the larger. | |
| High-level input voltage | V_IH | V | min | Recommended Operating Conditions / DC Characteristics, row "High-Level Input Voltage" at your V_CC. | |
| Low-level input voltage | V_IL | V | max | Same table, row "Low-Level Input Voltage". | |
| High-level output current | I_OH | A | max | Recommended Operating Conditions, row "High-Level Output Current" (magnitude). | |
| Low-level output current | I_OL | A | max | Recommended Operating Conditions, row "Low-Level Output Current". | |
| Quiescent supply current | I_CC | A | max | DC Characteristics, row "Supply Current" (static, inputs at a rail). | |
| Input capacitance | C_I | F | typ | DC / Switching Characteristics, row "Input Capacitance" (C_I). | |
| High-level output voltage | V_OH | V | min | Electrical Characteristics, row "High-Level Output Voltage" at the stated I_OH. | |
| Low-level output voltage | V_OL | V | max | Electrical Characteristics, row "Low-Level Output Voltage" at the stated I_OL. | |
| Output transition time | t_t | s | typ, max | Switching Characteristics, row "Transition Time" (t_t, t_r or t_f). | |
| Input leakage current | I_I | A | max | Electrical Characteristics, row "Input Current" (I_I). | |
| Off-state output current | I_OZ | A | max | Electrical Characteristics, row "Off-State Output Current" (three-state outputs). | |
| Gates per package | n | typ | Title and pinout: "quad 2-input" = 4. | ||
| Thermal resistance, junction to ambient | θ_JA | C/W | typ, max | Thermal Characteristics / Thermal Information table, row "Junction-to-Ambient" (R_θJA). Note the PCB it is quoted on (JEDEC 1s or 2s2p). | |
| Thermal resistance, junction to case | θ_JC | C/W | typ, max | Thermal Characteristics table, row "Junction-to-Case" (R_θJC). For power packages use the tab / bottom value. | |
| Maximum junction temperature | T_J(max) | C | max | Absolute Maximum Ratings table, row "Junction Temperature" or "Operating Junction Temperature" (T_J). | |
| Power dissipation | P_D | W | max | Absolute Maximum Ratings, row "Power Dissipation" (P_D or P_tot) at T_A = 25 °C. If only a derating curve exists read its 25 °C value. | |
| Pin count | N_pins | typ | Package / Pin Configuration drawing on page 1 or 2. Count every terminal including the exposed pad. |
Logic · Level translator (logic.lvlshift → device lvlshift)
Simulation pins: VCCA, VCCB, OE, GND, A1, A2, B1, B2. Symbol variants: txs2, txs8, 1t45, 2t45.
| Field | Symbol | Unit | Columns | Sets | Where to find it in the datasheet |
|---|---|---|---|---|---|
| Propagation delay | t_PD | s | typ, max | tpd | Switching characteristics at your VCCA / VCCB pair. |
| Internal pull-up (TXS) | R_PU | Ohm | typ | r_pu | Auto-direction parts: "Integrated pull-up resistors" (TXS0108: 10 kΩ / 4 kΩ). |
| VCCA range | V_CCA | V | min, max | Recommended operating conditions. | |
| VCCB range | V_CCB | V | min, max | Recommended operating conditions. | |
| Operating temperature range | T_op | C | min, max | Features or Recommended Operating Conditions, row "Operating Temperature Range" (minimum and maximum). | |
| Pin count | N_pins | typ | Package / Pin Configuration drawing on page 1 or 2. Count every terminal including the exposed pad. |
55.11Microcontrollers and programmable
MCU · Microcontroller (pin level) (mcu.mcu → device mcu)
Simulation pins: VDD, GND, PA0, PA1, PB0, PB1. Symbol variants: generic, atmega328p_tqfp32, attiny85_dip8, stm32f103c8_lqfp48.
| Field | Symbol | Unit | Columns | Sets | Where to find it in the datasheet |
|---|---|---|---|---|---|
| Supply voltage | V_DD | V | min, typ, max | vdd | Recommended operating conditions, "V_DD". |
| Run current | I_DD | A | typ | idd | Electrical characteristics, "Supply current, run mode" at your clock. |
| GPIO output resistance | R_OUT | Ohm | typ | I/O characteristics: V_OH / V_OL at I_OH / I_OL → (V_DD − V_OH) / I_OH. | |
| ADC resolution | N | bits | typ | ADC characteristics, "Resolution" (for pins mapped as ain). | |
| Operating temperature range | T_op | C | min, max | Features or Recommended Operating Conditions, row "Operating Temperature Range" (minimum and maximum). | |
| Pin count | N_pins | typ | Package / Pin Configuration drawing on page 1 or 2. Count every terminal including the exposed pad. |
55.12Mixed-signal
Mixed-signal · Digital potentiometer (mixed.digipot → device digipot)
Simulation pins: nINC, U_nD, VH, VSS, VW, VL, nCS, VCC. Symbol variants: updown, spi, i2c.
| Field | Symbol | Unit | Columns | Sets | Where to find it in the datasheet |
|---|---|---|---|---|---|
| End-to-end resistance * | R_AB | Ohm | typ | r | Ordering option, "Resistance" (X9C103 = 10 kΩ). |
| Number of taps * | N | typ | steps | "Resolution" / "Taps" (X9C: 100, MCP4131: 129). | |
| Wiper resistance | R_W | Ohm | typ, max | r_w | "Wiper resistance". |
| Operating temperature range | T_op | C | min, max | Features or Recommended Operating Conditions, row "Operating Temperature Range" (minimum and maximum). | |
| Pin count | N_pins | typ | Package / Pin Configuration drawing on page 1 or 2. Count every terminal including the exposed pad. |
55.13Motors and actuators
Motors · BLDC motor (motors.bldc → device bldc)
Simulation pins: u, v, w. Symbol variants: sensorless, hall.
| Field | Symbol | Unit | Columns | Sets | Where to find it in the datasheet |
|---|---|---|---|---|---|
| Velocity constant * | Kv | rpm/V | typ | kv | Specification, "KV". |
| Phase resistance * | R_ph | Ohm | typ | r_phase | "Internal resistance" (line-to-line / 2). |
| Pole count | p | typ | poles | "Configuration" (for example 12N14P → 14 poles). | |
| Phase inductance | L_ph | H | typ | l_phase | "Inductance" (line-to-line / 2). |
| Operating temperature range | T_op | C | min, max | Features or Recommended Operating Conditions, row "Operating Temperature Range" (minimum and maximum). | |
| Pin count | N_pins | typ | Package / Pin Configuration drawing on page 1 or 2. Count every terminal including the exposed pad. |
Motors · DC motor (motors.dcmotor → device dcmotor)
Simulation pins: +, −. Symbol variants: brushed, fan, vibration, gear.
| Field | Symbol | Unit | Columns | Sets | Where to find it in the datasheet |
|---|---|---|---|---|---|
| Rated voltage * | V_N | V | typ | v_rated | Specification table, "Rated voltage". |
| No-load speed * | n_0 | rpm | typ | rpm_noload | Specification table, "No-load speed". |
| No-load current | I_0 | A | typ | i_noload | Specification table, "No-load current". |
| Stall current * | I_S | A | typ | i_stall | Specification table, "Stall current" (or rated voltage / terminal resistance). |
| Stall torque | T_S | N·m | typ | Specification table, "Stall torque" (mN·m, g·cm × 9.81e-5). | |
| Terminal resistance | R | Ohm | typ | "Terminal resistance" (overrides V/I_stall). | |
| Terminal inductance | L | H | typ | l | "Terminal inductance". |
| Operating temperature range | T_op | C | min, max | Features or Recommended Operating Conditions, row "Operating Temperature Range" (minimum and maximum). | |
| Rotor inertia | J | kg·m² | typ | "Rotor inertia" (g·cm² × 1e-7). | |
| Gear ratio | i | typ | gear | Gear motors: "Reduction ratio". | |
| Pin count | N_pins | typ | Package / Pin Configuration drawing on page 1 or 2. Count every terminal including the exposed pad. |
Motors · Dual H-bridge driver (motors.hbridge2 → device hbridge2)
Simulation pins: AIN1, AIN2, BIN1, BIN2, AOUT1, AOUT2, BOUT1, BOUT2, VM, GND, nSLEEP. Symbol variants: in_in, pwm_dir.
| Field | Symbol | Unit | Columns | Sets | Where to find it in the datasheet |
|---|---|---|---|---|---|
| Output on resistance (HS + LS) * | R_DS(on) | Ohm | typ, max | ron | Electrical characteristics, "HS + LS on resistance". |
| Output current / limit | I_OUT | A | max | ilim | "Continuous output current" or "Overcurrent protection". |
| Motor supply range | V_M | V | min, max | Recommended operating conditions, "VM". | |
| Operating temperature range | T_op | C | min, max | Features or Recommended Operating Conditions, row "Operating Temperature Range" (minimum and maximum). | |
| Pin count | N_pins | typ | Package / Pin Configuration drawing on page 1 or 2. Count every terminal including the exposed pad. | ||
| Thermal resistance, junction to ambient | θ_JA | C/W | typ, max | Thermal characteristics table, "Thermal resistance junction to ambient". |
Motors · Peltier module (motors.peltier → device peltier)
Simulation pins: +, −.
| Field | Symbol | Unit | Columns | Sets | Where to find it in the datasheet |
|---|---|---|---|---|---|
| Max current * | I_max | A | max | Specification, "I_max". | |
| Max voltage * | V_max | V | max | r | Specification, "V_max" (r ≈ V_max / I_max at ΔT = 0). |
| Operating temperature range | T_op | C | min, max | Features or Recommended Operating Conditions, row "Operating Temperature Range" (minimum and maximum). | |
| Max temperature difference | ΔT_max | K | typ | seebeck | Specification, "ΔT_max" (fits the Seebeck coefficient). |
| Pin count | N_pins | typ | Package / Pin Configuration drawing on page 1 or 2. Count every terminal including the exposed pad. |
Motors · RC servo (motors.servo → device servo)
Simulation pins: sig, vcc, gnd. Symbol variants: analog, digital, continuous.
| Field | Symbol | Unit | Columns | Sets | Where to find it in the datasheet |
|---|---|---|---|---|---|
| Travel * | θ | deg | typ | range | Specification, "Operating angle" / "Travel". |
| Operating speed | ω | deg/s | typ | speed | Specification, "Speed" (s / 60° → 60 / value). |
| Pulse width at 0° | PW_min | s | typ | pw_min | "Pulse width range" (for example 500–2500 µs or 1000–2000 µs). |
| Pulse width at full travel | PW_max | s | typ | pw_max | Same row, upper end. |
| Stall current | I_stall | A | max | i_stall | "Stall current". |
| Idle current | I_idle | A | typ | i_idle | "Idle / standby current". |
| Operating voltage (min) | V_min | V | min | v_min | "Operating voltage". |
| Operating temperature range | T_op | C | min, max | Features or Recommended Operating Conditions, row "Operating Temperature Range" (minimum and maximum). | |
| Pin count | N_pins | typ | Package / Pin Configuration drawing on page 1 or 2. Count every terminal including the exposed pad. |
Motors · Solenoid (motors.solenoid → device solenoid)
Simulation pins: +, −. Symbol variants: pull, push, valve, lock.
| Field | Symbol | Unit | Columns | Sets | Where to find it in the datasheet |
|---|---|---|---|---|---|
| Rated voltage * | V_N | V | typ | v_rated | Specification, "Rated voltage". |
| Coil resistance * | R | Ohm | typ | r | Specification, "Coil resistance". |
| Operating temperature range | T_op | C | min, max | Features or Recommended Operating Conditions, row "Operating Temperature Range" (minimum and maximum). | |
| Stroke | s | m | typ | stroke | Specification, "Stroke" (mm). |
| Holding force | F | N | typ | Force vs stroke graph at rated voltage (informational. Fits l_in). | |
| Duty cycle | ED | % | max | "Duty cycle" (informational, W_RATING for long energisation). | |
| Pin count | N_pins | typ | Package / Pin Configuration drawing on page 1 or 2. Count every terminal including the exposed pad. |
Motors · Stepper driver (motors.stepdrv → device stepdrv)
Simulation pins: EN, MS1, MS2, MS3, RST, SLP, STEP, DIR, VMOT, GND, 1A, 1B, 2A, 2B, VDD, VREF. Symbol variants: a4988, drv8825.
| Field | Symbol | Unit | Columns | Sets | Where to find it in the datasheet |
|---|---|---|---|---|---|
| Sense resistor * | R_S | Ohm | typ | rsense | Module / board: the sense resistors (R100 = 0.1 Ω, R068 = 0.068 Ω). |
| Current limit | I_TRIP | A | typ | ilim | From VREF: A4988 I = VREF / (8 · R_S), DRV8825 I = VREF / (5 · R_S). |
| Output on resistance | R_DS(on) | Ohm | typ, max | ron | "Output on resistance" (source + sink). |
| Fixed off time | t_OFF | s | typ | toff | "Fixed off-time" (A4988 ~20 µs). |
| Operating temperature range | T_op | C | min, max | Features or Recommended Operating Conditions, row "Operating Temperature Range" (minimum and maximum). | |
| Pin count | N_pins | typ | Package / Pin Configuration drawing on page 1 or 2. Count every terminal including the exposed pad. | ||
| Thermal resistance, junction to ambient | θ_JA | C/W | typ, max | Thermal characteristics table, "Thermal resistance junction to ambient". |
Motors · Stepper motor (motors.stepper → device stepper)
Simulation pins: a+, a−, b+, b−. Symbol variants: bipolar, unipolar6, unipolar5.
| Field | Symbol | Unit | Columns | Sets | Where to find it in the datasheet |
|---|---|---|---|---|---|
| Step angle * | θ_step | deg | typ | steps | Specification table, "Step angle" (1.8° → 200 steps). |
| Rated current per phase * | I_N | A | typ | i_rated | Specification table, "Rated current" / "Current per phase". |
| Phase resistance * | R_ph | Ohm | typ | r_phase | Specification table, "Phase resistance". |
| Phase inductance | L_ph | H | typ | l_phase | Specification table, "Phase inductance". |
| Operating temperature range | T_op | C | min, max | Features or Recommended Operating Conditions, row "Operating Temperature Range" (minimum and maximum). | |
| Holding torque | T_H | N·m | typ | t_hold | Specification table, "Holding torque" (kg·cm × 0.098). |
| Detent torque | T_D | N·m | typ | t_detent | "Detent torque". |
| Rotor inertia | J | kg·m² | typ | j | "Rotor inertia" (g·cm² × 1e-7). |
| Gear ratio | i | typ | gear | Geared steppers (28BYJ-48: 63.68). | |
| Pin count | N_pins | typ | Package / Pin Configuration drawing on page 1 or 2. Count every terminal including the exposed pad. |
55.14Optoelectronics
Optoelectronics · Addressable LED (opto.ws2812 → device ws2812)
Simulation pins: VDD, DOUT, GND, DIN. Symbol variants: ws2812b, sk6812_rgbw.
| Field | Symbol | Unit | Columns | Sets | Where to find it in the datasheet |
|---|---|---|---|---|---|
| LED current per colour | I_LED | A | typ | i_led | Electrical characteristics, "LED output current" per channel at full brightness. |
| T0H (0 bit high time) | T0H | s | min, typ, max | Data transfer time table, "T0H". | |
| T1H (1 bit high time) | T1H | s | min, typ, max | t_th | Table, "T1H" (threshold t_th = (T0H + T1H) / 2). |
| Reset time | RES | s | min | t_reset | Table, "RES / Treset". |
| Quiescent supply current | I_DD | A | typ | idd | "Supply current" with LEDs off. |
| Operating temperature range | T_op | C | min, max | Features or Recommended Operating Conditions, row "Operating Temperature Range" (minimum and maximum). | |
| Pin count | N_pins | typ | Package / Pin Configuration drawing on page 1 or 2. Count every terminal including the exposed pad. |
Optoelectronics · IR receiver module (opto.irrx → device irrx)
Simulation pins: OUT, GND, VS.
| Field | Symbol | Unit | Columns | Sets | Where to find it in the datasheet |
|---|---|---|---|---|---|
| Carrier frequency * | f_0 | Hz | typ | f0 | Ordering table, "Carrier frequency" (36 / 38 / 40 / 56 kHz). |
| Supply voltage | V_S | V | min, max | Recommended operating conditions. | |
| Operating temperature range | T_op | C | min, max | Features or Recommended Operating Conditions, row "Operating Temperature Range" (minimum and maximum). | |
| Minimum burst length | t_pi | cycles | min | n_min | "Minimum burst length" (cycles). |
| Pin count | N_pins | typ | Package / Pin Configuration drawing on page 1 or 2. Count every terminal including the exposed pad. |
Optoelectronics · Lamp (opto.lamp → device lamp)
Simulation pins: a, b. Symbol variants: lamp, neon.
| Field | Symbol | Unit | Columns | Sets | Where to find it in the datasheet |
|---|---|---|---|---|---|
| Rated voltage * | V_N | V | typ | v_rated | Lamp data, "Voltage". |
| Rated power | P_N | W | typ | p_rated | Lamp data, "Wattage" (or I × V). |
| Striking voltage (neon) | V_S | V | max | v_strike | Neon lamps: "Striking voltage". |
| Maintaining voltage (neon) | V_M | V | typ | v_maint | Neon lamps: "Maintaining voltage". |
| Operating temperature range | T_op | C | min, max | Features or Recommended Operating Conditions, row "Operating Temperature Range" (minimum and maximum). | |
| Pin count | N_pins | typ | Package / Pin Configuration drawing on page 1 or 2. Count every terminal including the exposed pad. |
Optoelectronics · LED bar graph (opto.led_bar → device led_bar)
Simulation pins: a1, k1, a2, k2, a3, k3, a4, k4. Symbol variants: 4, 8, 10.
| Field | Symbol | Unit | Columns | Sets | Where to find it in the datasheet |
|---|---|---|---|---|---|
| Forward voltage * | V_F | V | typ, max | vf | Electro-optical characteristics, "Forward voltage" at I_F (per colour / segment). |
| Test current | I_F | A | typ | if_test | Condition of the V_F row (10 mA / 20 mA). |
| Max forward current | I_F(max) | A | max | Absolute maximum, "Forward current" (W_RATING). | |
| Operating temperature range | T_op | C | min, max | Features or Recommended Operating Conditions, row "Operating Temperature Range" (minimum and maximum). | |
| Pin count | N_pins | typ | Package / Pin Configuration drawing on page 1 or 2. Count every terminal including the exposed pad. |
Optoelectronics · Optocoupler (opto.opto → device opto)
Simulation pins: anode, cathode, collector, emitter. Symbol variants: transistor, transistor_b, darlington, triac, triac_zc, logic, slot, reflective.
| Field | Symbol | Unit | Columns | Sets | Where to find it in the datasheet |
|---|---|---|---|---|---|
| Current transfer ratio * | CTR | % | min, typ, max | ctr | Transfer characteristics, row "Current Transfer Ratio" at I_F and V_CE given in the conditions (rank letter: A 80-160 %, B 130-260 %…). |
| CTR test current | I_F | A | typ | if_test | Condition column of the CTR row (typically 5 mA or 10 mA). |
| LED forward voltage | V_F | V | typ, max | vf | Input characteristics, row "Forward Voltage" at I_F = 10 mA / 20 mA. |
| Collector-emitter saturation | V_CE(sat) | V | max | Transfer characteristics, row "Collector-emitter saturation voltage" (informational. Fit through bf). | |
| Rise / fall time | t_r | s | typ | tr | Switching characteristics, rows "Rise time" / "Fall time" at the given R_L. |
| Collector-emitter voltage | BV_CEO | V | min | bvceo | Absolute Maximum Ratings, row "Collector-emitter voltage". |
| Triac trigger current | I_FT | A | max | ift | Triac optos (MOC30xx): row "LED Trigger Current" (max). |
| Triac holding current | I_H | A | typ | ih | Triac optos: row "Holding Current". |
| Isolation voltage | V_ISO | V | min | Isolation characteristics, row "Isolation voltage" (Vrms, 1 min. Informational). | |
| Operating temperature range | T_op | C | min, max | Features or Recommended Operating Conditions, row "Operating Temperature Range" (minimum and maximum). | |
| Pin count | N_pins | typ | Package / Pin Configuration drawing on page 1 or 2. Count every terminal including the exposed pad. |
Optoelectronics · Photodiode (opto.photodiode → device photodiode)
Simulation pins: anode, cathode. Symbol variants: pin, ir, uv.
| Field | Symbol | Unit | Columns | Sets | Where to find it in the datasheet |
|---|---|---|---|---|---|
| Light current * | I_L | A | typ | s_lux | Electro-optical characteristics, "Reverse light current" at E_v (lx) or E_e (mW/cm²). Divide by the illuminance → s_lux. |
| Test illuminance | E_v | lx | typ | Condition of the light-current row (convert mW/cm² at 870 nm: × ~600 lx). | |
| Dark current | I_D | A | typ, max | i_dark | "Reverse dark current" at V_R. |
| Junction capacitance | C_D | F | typ | cj0 | "Diode capacitance" at V_R = 0 / 3 V. |
| Operating temperature range | T_op | C | min, max | Features or Recommended Operating Conditions, row "Operating Temperature Range" (minimum and maximum). | |
| Pin count | N_pins | typ | Package / Pin Configuration drawing on page 1 or 2. Count every terminal including the exposed pad. |
Optoelectronics · Phototransistor (opto.phototr → device phototr)
Simulation pins: collector, emitter. Symbol variants: 2pin, 3pin.
| Field | Symbol | Unit | Columns | Sets | Where to find it in the datasheet |
|---|---|---|---|---|---|
| Collector light current * | I_C(on) | A | min, typ | s_lux | Electro-optical characteristics, "Collector light current" at E_e / E_v, V_CE = 5 V. Divide by the illuminance → s_lux. |
| Test illuminance | E_v | lx | typ | Condition of that row (1 mW/cm² at 940 nm ≈ 700 lx equivalent). | |
| Dark current | I_CEO | A | max | i_dark | "Collector dark current". |
| Rise / fall time | t_r | s | typ | tr | "Rise time / fall time" at R_L. |
| Operating temperature range | T_op | C | min, max | Features or Recommended Operating Conditions, row "Operating Temperature Range" (minimum and maximum). | |
| Pin count | N_pins | typ | Package / Pin Configuration drawing on page 1 or 2. Count every terminal including the exposed pad. |
Optoelectronics · RGB LED (opto.led_rgb → device led_rgb)
Simulation pins: r, g, b, com. Symbol variants: cc, ca.
| Field | Symbol | Unit | Columns | Sets | Where to find it in the datasheet |
|---|---|---|---|---|---|
| Red forward voltage * | V_F(R) | V | typ, max | vf_r | Electro-optical table, red column, "V_F" at 20 mA. |
| Green forward voltage * | V_F(G) | V | typ, max | vf_g | Green column. |
| Blue forward voltage * | V_F(B) | V | typ, max | vf_b | Blue column. |
| Test current | I_F | A | typ | if_test | Condition of the V_F rows. |
| Operating temperature range | T_op | C | min, max | Features or Recommended Operating Conditions, row "Operating Temperature Range" (minimum and maximum). | |
| Pin count | N_pins | typ | Package / Pin Configuration drawing on page 1 or 2. Count every terminal including the exposed pad. |
55.15Passives
Passive · Capacitor (passive.capacitor → device cap)
Simulation pins: a, b. Curves: ESR vs frequency, Impedance vs frequency, Capacitance change vs DC bias, Capacitance change vs temperature.
| Field | Symbol | Unit | Columns | Sets | Where to find it in the datasheet |
|---|---|---|---|---|---|
| Capacitance * | C | F | min, typ, max | Part-number decoder or Ratings table, "Capacitance" (code 106 = 10 µF). For MLCCs check the DC-bias curve at your working voltage. | |
| Tolerance | ±tol | % | typ | Ordering code tolerance letter (K = 10 %, M = 20 %) or the Specifications table. | |
| Rated voltage | V_R | V | max | Ratings table, column "Rated Voltage" (WV or V_R). Do not use the surge voltage. | |
| Equivalent series resistance | ESR | Ohm | typ, max | Electrolytics: Standard Ratings table, column "ESR" or "Impedance" at 100 kHz, 20 °C. MLCC: the ESR vs frequency graph at the switching frequency. | |
| Rated ripple current | I_ripple | A | max | Standard Ratings table, column "Rated Ripple Current" (mA rms) at 105 °C, 100 kHz. Apply the frequency multiplier table for other frequencies. | |
| Leakage current | I_leak | A | max | Specifications table, row "Leakage Current" (often a formula like 0.01CV or 3 µA, after 2 minutes at rated voltage). | |
| Equivalent series inductance | ESL | H | typ | Impedance vs frequency graph: ESL = 1 / ((2π f_res)² C) from the self-resonant dip, or a stated ESL row. | |
| Dissipation factor | tan δ | max | Specifications table, row "Dissipation Factor (tan δ)" at 120 Hz. | ||
| Endurance (load life) | L_life | h | min | Specifications, row "Endurance" or "Load Life": hours at the maximum category temperature. | |
| Capacitance change over temperature | ΔC/C | % | typ, max | Dielectric code: X7R is ±15 %, X5R ±15 %, C0G ±0.3 % (30 ppm/°C), Y5V +22/−82 %. Or the "Capacitance vs Temperature" graph. | |
| Self-resonant frequency | f_SRF | Hz | typ | Impedance vs frequency graph: the frequency of the lowest impedance, or the SRF row. | |
| Insulation resistance | IR | Ohm | min | Electrical Specifications, row "Insulation Resistance" (or a time constant R·C in Ω·F). | |
| Operating temperature range | T_op | C | min, max | Features, row "Operating Temperature Range" (minimum and maximum). | |
| Aging rate | aging | % | typ | Electrical Specifications, row "Aging Rate" (percent per decade-hour, class II ceramics). | |
| Pin count | N_pins | typ | Package / Pin Configuration drawing on page 1 or 2. Count every terminal including the exposed pad. |
Passive · Common-mode choke (passives.cmc → device cmc)
Simulation pins: a1, b1, a2, b2. Curves: Common-mode impedance vs frequency, Differential impedance vs frequency.
| Field | Symbol | Unit | Columns | Sets | Where to find it in the datasheet |
|---|---|---|---|---|---|
| Inductance per winding * | L | H | min, typ | l | Ordering table, "Inductance" (per line, at 10 kHz / 100 kHz). |
| DC resistance per line | R_DC | Ohm | max | dcr | Ordering table, "DC Resistance". |
| Rated current | I_R | A | max | irated | Ordering table, "Rated Current". |
| Leakage inductance | L_leak | H | typ | k | "Leakage inductance" (→ k = 1 − L_leak / L). |
| Common-mode impedance at 100 MHz | Z_CM | Ohm | typ | Impedance graph or table (informational for USB / CAN chokes). | |
| Operating temperature range | T_op | C | min, max | Features or Recommended Operating Conditions, row "Operating Temperature Range" (minimum and maximum). | |
| Pin count | N_pins | typ | Package / Pin Configuration drawing on page 1 or 2. Count every terminal including the exposed pad. |
Passive · Dual potentiometer (passives.pot_dual → device pot_dual)
Simulation pins: a1, b1, w1, a2, b2, w2. Symbol variants: lin, log.
| Field | Symbol | Unit | Columns | Sets | Where to find it in the datasheet |
|---|---|---|---|---|---|
| Total resistance * | R | Ohm | typ | r | Ordering code, "Resistance" (B103 = 10 kΩ linear, A = log). |
| Taper | taper | typ | Ordering code taper letter: B linear, A audio (log), C reverse log → variant. | ||
| Tolerance | ±tol | % | typ | "Total resistance tolerance". | |
| Operating temperature range | T_op | C | min, max | Features or Recommended Operating Conditions, row "Operating Temperature Range" (minimum and maximum). | |
| Power rating | P | W | max | "Rated power". | |
| Pin count | N_pins | typ | Package / Pin Configuration drawing on page 1 or 2. Count every terminal including the exposed pad. |
Passive · Feed-through capacitor / EMI filter (passives.cap3 → device cap3)
Simulation pins: in, out, gnd.
| Field | Symbol | Unit | Columns | Sets | Where to find it in the datasheet |
|---|---|---|---|---|---|
| Capacitance * | C | F | typ | c | Ordering table, "Capacitance". |
| Rated current | I_R | A | max | Ordering table, "Rated current" (through conductor). | |
| DC resistance | R_DC | Ohm | max | rdc | Ordering table, "DC resistance". |
| Rated voltage | V_R | V | max | Ordering table, "Rated voltage". | |
| Operating temperature range | T_op | C | min, max | Features or Recommended Operating Conditions, row "Operating Temperature Range" (minimum and maximum). | |
| Pin count | N_pins | typ | Package / Pin Configuration drawing on page 1 or 2. Count every terminal including the exposed pad. |
Passive · Ferrite bead (passives.ferrite → device ferrite)
Simulation pins: a, b. Curves: Impedance vs frequency, Impedance vs DC bias current.
| Field | Symbol | Unit | Columns | Sets | Where to find it in the datasheet |
|---|---|---|---|---|---|
| Impedance at 100 MHz * | Z100 | Ohm | typ | z100 | Ordering table, column "Impedance at 100 MHz" (±25 %). |
| DC resistance | R_DC | Ohm | max | dcr | Ordering table, column "DC Resistance" (max). |
| Rated current | I_R | A | max | irated | Ordering table, column "Rated Current". |
| Impedance peak frequency | f_peak | Hz | typ | f_srf | Impedance vs frequency graph: frequency of the |Z| peak. |
| Operating temperature range | T_op | C | min, max | Features or Recommended Operating Conditions, row "Operating Temperature Range" (minimum and maximum). | |
| Pin count | N_pins | typ | Package / Pin Configuration drawing on page 1 or 2. Count every terminal including the exposed pad. |
Passive · Inductor (passive.inductor → device ind)
Simulation pins: a, b. Curves: Inductance vs DC current, Inductance vs frequency, Quality factor vs frequency, Impedance vs frequency, DC resistance vs temperature, Inductance change vs temperature.
| Field | Symbol | Unit | Columns | Sets | Where to find it in the datasheet |
|---|---|---|---|---|---|
| Inductance * | L | H | min, typ, max | Electrical Specifications table, column "Inductance" (L0 at 0 A, test frequency 100 kHz or 1 MHz). | |
| Tolerance | ±tol | % | typ | Table header or footnote, "Inductance tolerance" (typically ±20 %). | |
| DC resistance | DCR | Ohm | typ, max | Electrical Specifications table, column "DCR" (typ and max, mΩ, at 20 °C). | |
| Saturation current | I_sat | A | typ, max | Electrical Specifications table, column "I_sat": the current where L drops by 10 %, 20 % or 30 % (read the footnote for which). | |
| Rated (heating) current | I_rms | A | max | Electrical Specifications table, column "I_rms" or "I_rated": current for a 40 K temperature rise. | |
| Self-resonant frequency | SRF | Hz | min, typ | Electrical Specifications table, column "SRF" (MHz). Stay well below it. | |
| Saturation current at 30 % drop | I_sat(30) | A | typ, max | Electrical Specifications: the current where L has fallen by 30 % (I_sat). The 10 % and 20 % rows are the next fields. | |
| Current at 10 % inductance drop | I_sat(10) | A | typ, max | Electrical Specifications, row "I_sat" for a 10 % drop (some vendors call it I_DC1). | |
| Temperature rise at rated current | ΔT | C | typ | Electrical Specifications, the rise the rated I_rms causes (usually 40 °C). | |
| Quality factor | Q | typ | Electrical Specifications, row "Q" at the stated frequency (RF parts). | ||
| Parasitic winding capacitance | C_p | F | typ | Often implied by the self-resonant frequency (C_p = 1 / ((2π·SRF)² · L)). A few pF to nF. | |
| Inductance temperature coefficient | TCL | %/C | typ | Electrical Specifications or the L vs temperature graph (%/°C). | |
| Operating temperature range | T_op | C | min, max | Features, row "Operating Temperature Range". | |
| Shielded (1 = yes) | shield | typ | Product title or construction drawing: "shielded", "semi-shielded" or "unshielded". | ||
| Pin count | N_pins | typ | Package / Pin Configuration drawing on page 1 or 2. Count every terminal including the exposed pad. |
Passive · Resistor (passive.resistor → device res)
Simulation pins: a, b. Curves: Power derating, Impedance vs frequency.
| Field | Symbol | Unit | Columns | Sets | Where to find it in the datasheet |
|---|---|---|---|---|---|
| Resistance * | R | Ohm | typ | Ordering information or part-number decoder: the resistance code (for example 4K7 or 472 = 4.7 kΩ). | |
| Tolerance | ±tol | % | typ | Ordering information, tolerance letter (F = 1 %, J = 5 %), or the Electrical Specifications table. | |
| Power rating | P_R | W | max | Electrical Specifications table, row "Power Rating at 70 °C" (check the derating curve above that temperature). | |
| Maximum working voltage | V_max | V | max | Electrical Specifications table, row "Maximum Working Voltage" or "Limiting Element Voltage". | |
| Temperature coefficient | TCR | ppm/C | min, max | Electrical Specifications table, row "Temperature Coefficient" (ppm/°C), per resistance range. | |
| Parasitic inductance | L_s | H | typ | Rarely in the table. Look for "High Frequency Performance" or an impedance graph, else leave empty. | |
| Voltage coefficient | VCR | ppm/V | max | Electrical Specifications, row "Voltage Coefficient of Resistance" (precision and thick-film parts). | |
| Short-time overload voltage | V_ov | V | max | Electrical Specifications, row "Overload Voltage" (usually 2.5 times the rated voltage for 5 s). | |
| Rated ambient temperature | T_R | C | typ | Electrical Specifications, the temperature the power rating holds up to (usually 70 °C). | |
| Current noise index | NI | dB | typ | Electrical Specifications, row "Current Noise" (dB, µV/V per decade). | |
| Operating temperature range | T_op | C | min, max | Features or Recommended Operating Conditions, row "Operating Temperature Range" (minimum and maximum). | |
| Pin count | N_pins | typ | Package / Pin Configuration drawing on page 1 or 2. Count every terminal including the exposed pad. |
Passive · Resistor network (passives.rnet → device rnet)
Simulation pins: a1, b1, a2, b2, a3, b3, a4, b4. Symbol variants: iso4, iso2, iso8, bus4, bus8.
| Field | Symbol | Unit | Columns | Sets | Where to find it in the datasheet |
|---|---|---|---|---|---|
| Resistance * | R | Ohm | typ | r | Part-number decoder (for example 4D02WGJ0103 → 10 kΩ). |
| Number of resistors * | N | typ | Circuit diagram on page 1 (isolated / bussed and count) → variant. | ||
| Tolerance | ±tol | % | typ | tol | Tolerance letter (F 1 %, J 5 %). |
| Operating temperature range | T_op | C | min, max | Features or Recommended Operating Conditions, row "Operating Temperature Range" (minimum and maximum). | |
| Pin count | N_pins | typ | Package / Pin Configuration drawing on page 1 or 2. Count every terminal including the exposed pad. |
Passive · Transformer (passive.transformer → device xfmr)
Simulation pins: p1, p2, s1, s2.
| Field | Symbol | Unit | Columns | Sets | Where to find it in the datasheet |
|---|---|---|---|---|---|
| Primary inductance * | L_P | H | min, typ, max | Electrical Specifications table, row "Primary Inductance" (open-circuit, at the stated frequency and level). | |
| Turns ratio (secondary / primary) * | N_S/N_P | typ | Electrical Specifications, row "Turns Ratio". Write it as secondary over primary (1:0.1 for a 10:1 step-down). | ||
| Coupling coefficient | k | typ | Not usually listed: k = sqrt(1 − L_leak / L_P) from rows "Leakage Inductance" and "Primary Inductance". | ||
| Leakage inductance | L_lk | H | max | Electrical Specifications, row "Leakage Inductance" (measured with the secondary shorted). | |
| Primary DC resistance | DCR_P | Ohm | typ, max | Electrical Specifications, row "DCR Primary" or "Winding Resistance". | |
| Secondary DC resistance | DCR_S | Ohm | typ, max | Electrical Specifications, row "DCR Secondary". | |
| Isolation voltage | V_iso | V | min | Electrical Specifications, row "Hipot" or "Isolation" (Vrms for 1 minute). | |
| Primary saturation current | I_sat | A | max | Row "Saturation Current" or "Peak Current", if given (flyback transformers). | |
| Operating temperature range | T_op | C | min, max | Features or Recommended Operating Conditions, row "Operating Temperature Range" (minimum and maximum). | |
| Pin count | N_pins | typ | Package / Pin Configuration drawing on page 1 or 2. Count every terminal including the exposed pad. |
Passive · Transformer (multi-winding) (passives.xfmr_multi → device xfmr_multi)
Simulation pins: p1, p2, s1, sct, s2. Symbol variants: ct, ct_pri, dual, flyback, current.
| Field | Symbol | Unit | Columns | Sets | Where to find it in the datasheet |
|---|---|---|---|---|---|
| Primary inductance * | L_P | H | min, typ | lp | Electrical specifications, "Primary inductance" (at f, level). |
| Turns ratio (Np:Ns) * | n | typ | ratio | Electrical specifications, "Turns ratio" (Ns / Np as the ratio param). | |
| Second winding ratio | n2 | typ | ratio2 | Dual / flyback aux winding turns ratio. | |
| Leakage inductance | L_leak | H | max | k | "Leakage inductance" (secondaries shorted) → k. |
| Primary DCR | R_P | Ohm | max | rp | "DC resistance, primary". |
| Secondary DCR | R_S | Ohm | max | rs | "DC resistance, secondary". |
| Current transformer turns | N | typ | n | Current-sense transformers: "Turns ratio 1:N". | |
| Isolation voltage | V_ISO | V | min | "Hi-pot / isolation" (informational). | |
| Operating temperature range | T_op | C | min, max | Features or Recommended Operating Conditions, row "Operating Temperature Range" (minimum and maximum). | |
| Pin count | N_pins | typ | Package / Pin Configuration drawing on page 1 or 2. Count every terminal including the exposed pad. |
55.16Power management
Controller · Battery charger (controller.charger → device chgctl)
Simulation pins: vin, bat, gnd, cs, gate. Symbol variants: cccv, float.
| Field | Symbol | Unit | Columns | Sets | Where to find it in the datasheet |
|---|---|---|---|---|---|
| Float / regulation voltage * | V_FLOAT | V | min, typ, max | Electrical Characteristics, row "Regulated Output (Float) Voltage" / "V_BAT(REG)" for your cell count option. | |
| Fast-charge current (as programmed) * | I_CHG | A | min, typ, max | Programming section: I_CHG formula with your R_PROG / R_SENSE (for example I = V_CS / R_SENSE or 1000 V / R_PROG). | |
| Termination current | I_TERM | A | min, typ, max | Electrical Characteristics, row "Termination Current Threshold" (often C/10 of I_CHG). | |
| Pre-charge current | I_PRE | A | min, typ, max | Electrical Characteristics, row "Pre-charge / Trickle Current". | |
| Pre-charge threshold | V_PRE | V | min, typ, max | Electrical Characteristics, row "Pre-charge Threshold Voltage". | |
| Input voltage range | V_IN | V | min, max | Recommended Operating Conditions, row "Input Voltage". | |
| Current-sense threshold | V_CS | V | min, typ, max | Electrical Characteristics, row "Current Sense Voltage" (switching chargers with an external shunt). | |
| Switching frequency | f_SW | Hz | typ | Switching chargers: row "Oscillator Frequency". Empty for linear chargers. | |
| Safety timer | t_TIMER | s | typ | Timer section, row "Charge Safety Timer". | |
| Thermal resistance, junction to ambient | θ_JA | C/W | typ, max | Thermal Characteristics / Thermal Information table, row "Junction-to-Ambient" (R_θJA). Note the PCB it is quoted on (JEDEC 1s or 2s2p). | |
| Thermal resistance, junction to case | θ_JC | C/W | typ, max | Thermal Characteristics table, row "Junction-to-Case" (R_θJC). For power packages use the tab / bottom value. | |
| Maximum junction temperature | T_J(max) | C | max | Absolute Maximum Ratings table, row "Junction Temperature" or "Operating Junction Temperature" (T_J). | |
| Power dissipation | P_D | W | max | Absolute Maximum Ratings, row "Power Dissipation" (P_D or P_tot) at T_A = 25 °C. If only a derating curve exists read its 25 °C value. | |
| Pin count | N_pins | typ | Package / Pin Configuration drawing on page 1 or 2. Count every terminal including the exposed pad. |
Controller · LED driver (controller.led → device ledctl)
Simulation pins: vin, gnd, cs, gate, dim. Symbol variants: buck_cc, boost_cc.
| Field | Symbol | Unit | Columns | Sets | Where to find it in the datasheet |
|---|---|---|---|---|---|
| Current-sense regulation voltage * | V_CS | V | min, typ, max | Electrical Characteristics, row "Current Sense Threshold" / "V_CS": I_LED = V_CS / R_SENSE (average or peak, say which in the note). | |
| Switching frequency * | f_SW | Hz | min, typ, max | Oscillator section, row "Switching Frequency" (or the hysteretic frequency formula). | |
| Input voltage range | V_IN | V | min, max | Recommended Operating Conditions, row "Input Voltage". | |
| Maximum PWM dimming frequency | f_DIM | Hz | max | Dimming section, row "PWM Dimming Frequency" or minimum DIM pulse width. | |
| DIM pin threshold | V_DIM | V | typ | Dimming section, row "DIM High / Low Threshold". | |
| Operating supply current | I_Q | A | typ, max | Electrical Characteristics, row "Quiescent Current". | |
| Gate drive source current | I_SOURCE | A | typ | Gate Driver section, row "Source Current". | |
| Gate drive sink current | I_SINK | A | typ | Gate Driver section, row "Sink Current". | |
| Thermal resistance, junction to ambient | θ_JA | C/W | typ, max | Thermal Characteristics / Thermal Information table, row "Junction-to-Ambient" (R_θJA). Note the PCB it is quoted on (JEDEC 1s or 2s2p). | |
| Thermal resistance, junction to case | θ_JC | C/W | typ, max | Thermal Characteristics table, row "Junction-to-Case" (R_θJC). For power packages use the tab / bottom value. | |
| Maximum junction temperature | T_J(max) | C | max | Absolute Maximum Ratings table, row "Junction Temperature" or "Operating Junction Temperature" (T_J). | |
| Power dissipation | P_D | W | max | Absolute Maximum Ratings, row "Power Dissipation" (P_D or P_tot) at T_A = 25 °C. If only a derating curve exists read its 25 °C value. | |
| Pin count | N_pins | typ | Package / Pin Configuration drawing on page 1 or 2. Count every terminal including the exposed pad. |
Controller · PWM (DC-DC / PFC) (controller.pwm → device pwmctl)
Simulation pins: vin, gnd, fb, comp, cs, gate, ss, en, rt. Symbol variants: vmode, cmode, hyst, cot, pfc_tm, llc, qr.
| Field | Symbol | Unit | Columns | Sets | Where to find it in the datasheet |
|---|---|---|---|---|---|
| Feedback reference voltage * | V_FB | V | min, typ, max | Electrical Characteristics, row "Feedback Voltage" / "Reference Voltage" / "Error Amplifier Reference" (the FB pin regulation point). | |
| Switching frequency * | f_SW | Hz | min, typ, max | Oscillator section: row "Frequency" at your RT / CT values, or the f_SW vs R_T graph. | |
| Maximum duty cycle * | D_MAX | min, typ | Oscillator / PWM section, row "Maximum Duty Cycle" (store 0.95 for 95 %. 0.5 for single-output push-pull parts). | ||
| Minimum duty cycle | D_MIN | max | PWM section, row "Minimum Duty Cycle" or minimum on-time × f_SW. | ||
| Error amplifier open-loop gain | A_VOL | dB | min, typ | Error Amplifier section, row "Open-Loop Voltage Gain" (voltage-output error amps). | |
| Error amplifier transconductance | g_m | S | min, typ, max | Error Amplifier section, row "Transconductance" (gm-type error amps, µmho = µS). | |
| Error amplifier bandwidth | GBW | Hz | typ | Error Amplifier section, row "Unity Gain Bandwidth". | |
| Current-sense limit threshold | V_CS(max) | V | min, typ, max | Current Sense section, row "Maximum Input Signal" / "Current Limit Threshold" (V at the CS pin). | |
| Current-sense gain | A_CS | V/V | typ | Current Sense section, row "Gain" (for example 3 V/V on UC3843: COMP-to-CS ratio). | |
| Slope compensation | S_e | V/s | typ | Current-mode parts: row "Slope Compensation" (mV/µs or µA through R_SLOPE). Store V/s. | |
| Soft-start time | t_SS | s | typ | Soft-Start section: internal t_SS, or t_SS = C_SS · V / I_SS with the stated charge current. | |
| UVLO start threshold | V_ON | V | min, typ, max | Under-Voltage Lockout section, row "Start Threshold" (rising V_CC / V_IN). | |
| UVLO stop threshold | V_OFF | V | min, typ, max | Under-Voltage Lockout section, row "Minimum Operating Voltage" (falling). | |
| Gate drive source current | I_SOURCE | A | typ | Output section, row "Peak Source Current" (or output resistance R_OH: I ≈ V_CC / R_OH). | |
| Gate drive sink current | I_SINK | A | typ | Output section, row "Peak Sink Current". | |
| Dead time | t_D | s | typ | Synchronous / push-pull parts: row "Dead Time" or "Shoot-Through Delay". | |
| Leading-edge blanking | t_LEB | s | typ | Current Sense section, row "Leading Edge Blanking Time". | |
| On-time (COT parts) | t_ON | s | typ | Constant-on-time parts: row "On-Time" at your R_ON / V_IN. | |
| Supply / input voltage range | V_IN | V | min, max | Recommended Operating Conditions, row "V_CC" / "V_IN". | |
| Operating supply current | I_CC | A | typ, max | Supply section, row "Operating Supply Current" (not switching, or with the stated load). | |
| Thermal resistance, junction to ambient | θ_JA | C/W | typ, max | Thermal Characteristics / Thermal Information table, row "Junction-to-Ambient" (R_θJA). Note the PCB it is quoted on (JEDEC 1s or 2s2p). | |
| Thermal resistance, junction to case | θ_JC | C/W | typ, max | Thermal Characteristics table, row "Junction-to-Case" (R_θJC). For power packages use the tab / bottom value. | |
| Maximum junction temperature | T_J(max) | C | max | Absolute Maximum Ratings table, row "Junction Temperature" or "Operating Junction Temperature" (T_J). | |
| Power dissipation | P_D | W | max | Absolute Maximum Ratings, row "Power Dissipation" (P_D or P_tot) at T_A = 25 °C. If only a derating curve exists read its 25 °C value. | |
| Pin count | N_pins | typ | Package / Pin Configuration drawing on page 1 or 2. Count every terminal including the exposed pad. |
Driver · Gate driver (driver.gate → device gatedrv)
Simulation pins: hin, lin, vdd, gnd, ho, hs, lo, vb. Symbol variants: low, high_boot, half_bridge, isolated.
| Field | Symbol | Unit | Columns | Sets | Where to find it in the datasheet |
|---|---|---|---|---|---|
| Supply voltage range * | V_DD | V | min, max | Recommended Operating Conditions, row "V_DD" / "V_CC" (low-side supply). | |
| Supply UVLO threshold (rising) | V_DD(on) | V | min, typ, max | Electrical Characteristics, row "V_DD Under-Voltage Lockout, rising". | |
| Peak source current * | I_OH | A | min, typ | Electrical Characteristics, row "Peak Output Current, Source" (or 'Output High Short-Circuit Pulsed Current'). | |
| Peak sink current * | I_OL | A | min, typ | Electrical Characteristics, row "Peak Output Current, Sink". | |
| Propagation delay * | t_PD | s | typ, max | Switching Characteristics, rows t_ON / t_OFF (input to output). Use the larger. | |
| Output rise time | t_r | s | typ, max | Switching Characteristics, row "Rise Time" at C_L = 1 nF. | |
| Output fall time | t_f | s | typ, max | Switching Characteristics, row "Fall Time" at C_L = 1 nF. | |
| Built-in dead time | t_DT | s | min, typ, max | Half-bridge drivers: row "Dead Time". 0 for drivers that pass HIN / LIN straight through. | |
| Delay matching | t_MT | s | max | Switching Characteristics, row "Delay Matching" (high vs low side). | |
| Bootstrap / high-side offset voltage | V_HB / V_S | V | max | Absolute Maximum Ratings, row "High-Side Floating Offset Voltage" (V_S) or "V_HB". | |
| Quiescent supply current | I_QDD | A | typ, max | Electrical Characteristics, row "Quiescent V_DD Supply Current". | |
| Thermal resistance, junction to ambient | θ_JA | C/W | typ, max | Thermal Characteristics / Thermal Information table, row "Junction-to-Ambient" (R_θJA). Note the PCB it is quoted on (JEDEC 1s or 2s2p). | |
| Thermal resistance, junction to case | θ_JC | C/W | typ, max | Thermal Characteristics table, row "Junction-to-Case" (R_θJC). For power packages use the tab / bottom value. | |
| Maximum junction temperature | T_J(max) | C | max | Absolute Maximum Ratings table, row "Junction Temperature" or "Operating Junction Temperature" (T_J). | |
| Power dissipation | P_D | W | max | Absolute Maximum Ratings, row "Power Dissipation" (P_D or P_tot) at T_A = 25 °C. If only a derating curve exists read its 25 °C value. | |
| Pin count | N_pins | typ | Package / Pin Configuration drawing on page 1 or 2. Count every terminal including the exposed pad. |
Power · Battery protection IC (power.batprot → device batprot)
Simulation pins: OD, CS, OC, TD, VCC, GND.
| Field | Symbol | Unit | Columns | Sets | Where to find it in the datasheet |
|---|---|---|---|---|---|
| Overcharge detection * | V_OCP | V | min, typ, max | v_oc | Electrical characteristics, "Overcharge detection voltage". |
| Overdischarge detection * | V_ODP | V | min, typ, max | v_od | "Overdischarge detection voltage". |
| Overcurrent detection | V_OI1 | V | min, typ, max | v_ocp | "Overcurrent detection voltage" (V at CS). |
| Overcharge delay | t_OC | s | typ | t_oc | "Overcharge detection delay time". |
| Overdischarge delay | t_OD | s | typ | t_od | "Overdischarge detection delay time". |
| Overcurrent delay | t_OI1 | s | typ | t_ocp | "Overcurrent detection delay time". |
| Operating temperature range | T_op | C | min, max | Features or Recommended Operating Conditions, row "Operating Temperature Range" (minimum and maximum). | |
| Pin count | N_pins | typ | Package / Pin Configuration drawing on page 1 or 2. Count every terminal including the exposed pad. |
Power · Boost converter IC (power.boostic → device boostic)
Simulation pins: SW, GND, FB, EN, VIN. Symbol variants: async, sync.
| Field | Symbol | Unit | Columns | Sets | Where to find it in the datasheet |
|---|---|---|---|---|---|
| Feedback voltage * | V_FB | V | min, typ, max | vref | Electrical characteristics, "Feedback voltage" (MT3608: 0.6 V). |
| Switching frequency * | f_SW | Hz | min, typ, max | fsw | "Switching frequency". |
| Switch current limit | I_LIM | A | min, typ | ilim | "Switch current limit". |
| Switch on resistance | R_DS(on) | Ohm | typ | ron | "Switch on resistance". |
| Maximum duty cycle | D_max | min | dmax | "Maximum duty cycle". | |
| Operating temperature range | T_op | C | min, max | Features or Recommended Operating Conditions, row "Operating Temperature Range" (minimum and maximum). | |
| Pin count | N_pins | typ | Package / Pin Configuration drawing on page 1 or 2. Count every terminal including the exposed pad. | ||
| Thermal resistance, junction to ambient | θ_JA | C/W | typ, max | Thermal characteristics table, "Thermal resistance junction to ambient". |
Power · Buck converter IC (power.buckic → device buckic)
Simulation pins: VIN, SW, GND, FB, EN, BST. Symbol variants: async, sync, module.
| Field | Symbol | Unit | Columns | Sets | Where to find it in the datasheet |
|---|---|---|---|---|---|
| Feedback voltage * | V_FB | V | min, typ, max | vref | Electrical characteristics, "Feedback voltage" (0.8 V / 0.6 V / 1.23 V). |
| Switching frequency * | f_SW | Hz | min, typ, max | fsw | "Switching frequency" (or the RT / FREQ formula). |
| Switch current limit | I_LIM | A | min, typ | ilim | "High-side switch current limit" / "Peak current limit". |
| High-side switch R_DS(on) | R_HS | Ohm | typ | ron_hs | "High-side switch on resistance". |
| Low-side switch R_DS(on) | R_LS | Ohm | typ | ron_ls | Synchronous parts: "Low-side switch on resistance". |
| Soft-start time | t_SS | s | typ | ss_time | "Soft-start time" (internal) or formula with C_SS. |
| Input voltage range | V_IN | V | min, max | Recommended operating conditions. | |
| Quiescent current | I_Q | A | typ, max | iq | "Quiescent current, not switching". |
| Operating temperature range | T_op | C | min, max | Features or Recommended Operating Conditions, row "Operating Temperature Range" (minimum and maximum). | |
| Pin count | N_pins | typ | Package / Pin Configuration drawing on page 1 or 2. Count every terminal including the exposed pad. | ||
| Thermal resistance, junction to ambient | θ_JA | C/W | typ, max | Thermal characteristics table, "Thermal resistance junction to ambient". |
Power · LDO regulator IC (power.ldo → device ldo)
Simulation pins: IN, GND, OUT. Symbol variants: fixed3, adj3, en5, en_pg, neg3, ams1117, adj5. Curves: Dropout vs load current, PSRR vs frequency.
| Field | Symbol | Unit | Columns | Sets | Where to find it in the datasheet |
|---|---|---|---|---|---|
| Output voltage * | V_OUT | V | min, typ, max | vset | Electrical characteristics, "Output voltage" (fixed option in the part number). |
| Reference / ADJ voltage | V_REF | V | min, typ, max | vref | Adjustable parts: "Reference voltage" (V_OUT − V_ADJ, 1.25 V for LM317 / AMS1117-ADJ). |
| Dropout voltage | V_DO | V | typ, max | vdo | "Dropout voltage" at the stated load (use the row at your current). |
| Output current / limit | I_LIM | A | min, typ | ilim | "Output current limit" or "Maximum output current". |
| Quiescent current | I_Q | A | typ, max | iq | "Quiescent / ground current" at no load. |
| Enable threshold | V_EN | V | min, max | ven_on | "EN input high threshold". |
| Shutdown current | I_SD | A | typ, max | Electrical Characteristics, row "Shutdown Current" with EN low. | |
| Line regulation | ΔV/ΔV_IN | %/V | typ, max | Electrical Characteristics, row "Line Regulation". | |
| Load regulation | ΔV/ΔI | % | typ, max | Electrical Characteristics, row "Load Regulation". | |
| Short-circuit current | I_SC | A | typ | Electrical Characteristics, row "Short-Circuit Current". | |
| Start-up time | t_on | s | typ, max | Electrical Characteristics, row "Turn-On Time". | |
| Operating temperature range | T_op | C | min, max | Features or Recommended Operating Conditions, row "Operating Temperature Range" (minimum and maximum). | |
| PSRR | PSRR | dB | typ | psrr_db | "PSRR" at 1 kHz. |
| Output noise | e_n | V | typ | Electrical Characteristics, row "Output Noise Voltage" (10 Hz to 100 kHz). | |
| Pin count | N_pins | typ | Package / Pin Configuration drawing on page 1 or 2. Count every terminal including the exposed pad. | ||
| Thermal resistance, junction to ambient | θ_JA | C/W | typ, max | Thermal characteristics table, "Thermal resistance junction to ambient". |
Power · Li-ion charger IC (power.charger → device charger)
Simulation pins: TEMP, PROG, GND, VCC, BAT, STDBY, CHRG, CE. Symbol variants: tp4056, mcp73831.
| Field | Symbol | Unit | Columns | Sets | Where to find it in the datasheet |
|---|---|---|---|---|---|
| Regulation (float) voltage * | V_FLOAT | V | min, typ, max | vfloat | Electrical characteristics, "Regulated output (float) voltage". |
| PROG current constant * | K_PROG | V | typ | k_prog | Charge-current formula: I_BAT = K / R_PROG (TP4056: 1200 V, MCP73831: 1000 V). |
| Termination current ratio | I_TERM / I_CHG | typ | i_term | "Termination current" (C/10 → 0.1). | |
| Trickle-charge threshold | V_TRIKL | V | typ | v_trickle | "Trickle charge threshold voltage". |
| Operating temperature range | T_op | C | min, max | Features or Recommended Operating Conditions, row "Operating Temperature Range" (minimum and maximum). | |
| Pin count | N_pins | typ | Package / Pin Configuration drawing on page 1 or 2. Count every terminal including the exposed pad. | ||
| Thermal resistance, junction to ambient | θ_JA | C/W | typ, max | Thermal characteristics table, "Thermal resistance junction to ambient". |
Power · Load switch / eFuse / ideal diode (power.loadsw → device loadsw)
Simulation pins: VIN, VOUT, ON, GND. Symbol variants: loadsw, efuse, ideal_diode, hiside.
| Field | Symbol | Unit | Columns | Sets | Where to find it in the datasheet |
|---|---|---|---|---|---|
| On resistance * | R_ON | Ohm | typ, max | ron | Electrical characteristics, "ON-state resistance" at your V_IN. |
| Output rise time | t_R | s | typ | t_rise | Switching characteristics, "V_OUT rise time" (often set by CT). |
| Current limit | I_LIM | A | min, typ, max | ilim | "Current limit" (eFuse: formula with R_ILIM → k_ilim). |
| ON threshold | V_IH | V | max | von | "ON pin high-level input voltage". |
| Quiescent current | I_Q | A | typ, max | iq | "Quiescent current". |
| Input voltage range | V_IN | V | min, max | Recommended operating conditions. | |
| Operating temperature range | T_op | C | min, max | Features or Recommended Operating Conditions, row "Operating Temperature Range" (minimum and maximum). | |
| Pin count | N_pins | typ | Package / Pin Configuration drawing on page 1 or 2. Count every terminal including the exposed pad. | ||
| Thermal resistance, junction to ambient | θ_JA | C/W | typ, max | Thermal characteristics table, "Thermal resistance junction to ambient". |
Power · Off-line switcher IC (power.offline → device offline)
Simulation pins: D, S, FB, BP. Symbol variants: buck, flyback.
| Field | Symbol | Unit | Columns | Sets | Where to find it in the datasheet |
|---|---|---|---|---|---|
| Current limit * | I_LIMIT | A | min, typ, max | ilim | Electrical characteristics, "Current limit". |
| Switching frequency * | f_OSC | Hz | min, typ, max | fsw | "Output frequency". |
| Feedback threshold | V_FB | V | typ | vfb | "Feedback pin voltage" / "FB threshold". |
| MOSFET on resistance | R_DS(on) | Ohm | typ, max | rds_on | "ON-state resistance" at 25 °C. |
| Breakdown voltage | BV_DSS | V | min | vdss | Absolute maximum, "Drain voltage". |
| Operating temperature range | T_op | C | min, max | Features or Recommended Operating Conditions, row "Operating Temperature Range" (minimum and maximum). | |
| Pin count | N_pins | typ | Package / Pin Configuration drawing on page 1 or 2. Count every terminal including the exposed pad. | ||
| Thermal resistance, junction to ambient | θ_JA | C/W | typ, max | Thermal characteristics table, "Thermal resistance junction to ambient". |
Power · Power supply module (power.psu_module → device psu_module)
Simulation pins: VIN, GND, VOUT, EN. Symbol variants: dcdc, dcdc_iso, acdc.
| Field | Symbol | Unit | Columns | Sets | Where to find it in the datasheet |
|---|---|---|---|---|---|
| Output voltage * | V_OUT | V | typ | vout | Selection table, "Output voltage". |
| Output power * | P_OUT | W | max | pout | Selection table, "Output power" (or V × I). |
| Efficiency | η | typ | eff | Selection table, "Efficiency" at full load. | |
| Input voltage range | V_IN | V | min, max | vin_min | Input specifications, "Input voltage range". |
| Output ripple and noise | V_rip | V | max | ripple | Output specifications, "Ripple &. Noise" (mVp-p, 20 MHz BW). |
| Isolation voltage | V_ISO | V | min | "Isolation voltage" (informational). | |
| Operating temperature range | T_op | C | min, max | Features or Recommended Operating Conditions, row "Operating Temperature Range" (minimum and maximum). | |
| Pin count | N_pins | typ | Package / Pin Configuration drawing on page 1 or 2. Count every terminal including the exposed pad. |
Regulator · Boost module (regulator.boost → device reg boost)
Simulation pins: in, out, gnd, en. Curves: Efficiency vs output current, Efficiency vs input voltage, Output voltage vs load current, Quiescent current vs input voltage.
| Field | Symbol | Unit | Columns | Sets | Where to find it in the datasheet |
|---|---|---|---|---|---|
| Input voltage range * | V_IN | V | min, max | Module: product table "Input Voltage". IC: Recommended Operating Conditions, row "Input Voltage". | |
| Output voltage (as set) * | V_OUT | V | min, typ, max | Module: the set output (or the feedback divider formula, V_OUT = V_FB·(1 + R1/R2)). IC: "Feedback Voltage" row and your divider. | |
| Maximum output current * | I_OUT(max) | A | max | Product table "Output Current" (continuous. Module ratings often need airflow, read the derating curve). | |
| Efficiency at typical load * | η | typ | Graph "Efficiency vs Output Current" at your V_IN / V_OUT, read at your load. Store 0.9 for 90 %. | ||
| Switching frequency * | f_SW | Hz | min, typ, max | Electrical Characteristics, row "Switching Frequency" (f_SW or f_OSC). | |
| Output ripple (peak-to-peak) | V_RIPPLE | V | typ, max | Module: specification "Output Ripple" (mVpp, 20 MHz bandwidth). IC: the steady-state switching waveform in Typical Characteristics. | |
| Switch current limit | I_LIM | A | min, typ | Electrical Characteristics, row "Switch Current Limit" or "Peak Current Limit". | |
| Quiescent / no-load input current | I_Q | A | typ, max | Electrical Characteristics, row "Quiescent Current" (switching, no load) or module no-load input current. | |
| Soft-start time | t_SS | s | typ | Electrical Characteristics, row "Soft-Start Time". Sets the live model response time constant. | |
| High-side switch on-resistance | R_DS(on),HS | Ohm | typ | Electrical Characteristics, row "High-Side Switch On Resistance" (integrated-switch ICs). | |
| Minimum V_OUT above V_IN | V_OUT − V_IN | V | min | Application Information: a boost cannot regulate when V_IN approaches V_OUT. Note the stated margin (output then follows V_IN − V_F). | |
| Feedback reference voltage | V_FB | V | typ, max | Electrical Characteristics, row "Feedback Voltage" or "Reference Voltage" (V_FB). | |
| Minimum on-time | t_on(min) | s | typ | Electrical Characteristics, row "Minimum On-Time". | |
| Shutdown current | I_SD | A | typ, max | Electrical Characteristics, row "Shutdown Current" with EN low. | |
| Input undervoltage lockout, rising | V_UVLO | V | typ | Electrical Characteristics, row "UVLO Threshold, Rising". | |
| Input undervoltage lockout, falling | V_UVLO | V | typ | Electrical Characteristics, row "UVLO Threshold, Falling". | |
| Line regulation | ΔV/ΔV_IN | %/V | typ | Electrical Characteristics, row "Line Regulation". | |
| Load regulation | ΔV/ΔI | % | typ | Electrical Characteristics, row "Load Regulation". | |
| Thermal resistance, junction to ambient | θ_JA | C/W | typ, max | Thermal Characteristics / Thermal Information table, row "Junction-to-Ambient" (R_θJA). Note the PCB it is quoted on (JEDEC 1s or 2s2p). | |
| Thermal resistance, junction to case | θ_JC | C/W | typ, max | Thermal Characteristics table, row "Junction-to-Case" (R_θJC). For power packages use the tab / bottom value. | |
| Maximum junction temperature | T_J(max) | C | max | Absolute Maximum Ratings table, row "Junction Temperature" or "Operating Junction Temperature" (T_J). | |
| Power dissipation | P_D | W | max | Absolute Maximum Ratings, row "Power Dissipation" (P_D or P_tot) at T_A = 25 °C. If only a derating curve exists read its 25 °C value. | |
| Thermal shutdown temperature | T_SD | C | typ | Electrical Characteristics, row "Thermal Shutdown". | |
| Pin count | N_pins | typ | Package / Pin Configuration drawing on page 1 or 2. Count every terminal including the exposed pad. |
Regulator · Buck module (regulator.buck → device reg buck)
Simulation pins: in, out, gnd, en. Curves: Efficiency vs output current, Efficiency vs input voltage, Output voltage vs load current, Quiescent current vs input voltage, Switching frequency vs load current.
| Field | Symbol | Unit | Columns | Sets | Where to find it in the datasheet |
|---|---|---|---|---|---|
| Input voltage range * | V_IN | V | min, max | Module: product table "Input Voltage". IC: Recommended Operating Conditions, row "Input Voltage". | |
| Output voltage (as set) * | V_OUT | V | min, typ, max | Module: the set output (or the feedback divider formula, V_OUT = V_FB·(1 + R1/R2)). IC: "Feedback Voltage" row and your divider. | |
| Maximum output current * | I_OUT(max) | A | max | Product table "Output Current" (continuous. Module ratings often need airflow, read the derating curve). | |
| Efficiency at typical load * | η | typ | Graph "Efficiency vs Output Current" at your V_IN / V_OUT, read at your load. Store 0.9 for 90 %. | ||
| Switching frequency * | f_SW | Hz | min, typ, max | Electrical Characteristics, row "Switching Frequency" (f_SW or f_OSC). | |
| Output ripple (peak-to-peak) | V_RIPPLE | V | typ, max | Module: specification "Output Ripple" (mVpp, 20 MHz bandwidth). IC: the steady-state switching waveform in Typical Characteristics. | |
| Switch current limit | I_LIM | A | min, typ | Electrical Characteristics, row "Switch Current Limit" or "Peak Current Limit". | |
| Quiescent / no-load input current | I_Q | A | typ, max | Electrical Characteristics, row "Quiescent Current" (switching, no load) or module no-load input current. | |
| Soft-start time | t_SS | s | typ | Electrical Characteristics, row "Soft-Start Time". Sets the live model response time constant. | |
| High-side switch on-resistance | R_DS(on),HS | Ohm | typ | Electrical Characteristics, row "High-Side Switch On Resistance" (integrated-switch ICs). | |
| Inductor value (module / recommended) | L | H | typ | Module: BOM or schematic. IC: Application Information "Inductor Selection" table. | |
| Feedback reference voltage | V_FB | V | typ, max | Electrical Characteristics, row "Feedback Voltage" or "Reference Voltage" (V_FB). | |
| Maximum duty cycle | D_max | typ | Electrical Characteristics, row "Maximum Duty Cycle". | ||
| Minimum on-time | t_on(min) | s | typ | Electrical Characteristics, row "Minimum On-Time". | |
| Shutdown current | I_SD | A | typ, max | Electrical Characteristics, row "Shutdown Current" with EN low. | |
| Input undervoltage lockout, rising | V_UVLO | V | typ | Electrical Characteristics, row "UVLO Threshold, Rising". | |
| Input undervoltage lockout, falling | V_UVLO | V | typ | Electrical Characteristics, row "UVLO Threshold, Falling". | |
| Low-side switch on-resistance | R_DS(on) | Ohm | typ, max | Electrical Characteristics, row "Low-Side MOSFET On-Resistance" (synchronous parts). | |
| Line regulation | ΔV/ΔV_IN | %/V | typ | Electrical Characteristics, row "Line Regulation". | |
| Load regulation | ΔV/ΔI | % | typ | Electrical Characteristics, row "Load Regulation". | |
| Thermal resistance, junction to ambient | θ_JA | C/W | typ, max | Thermal Characteristics / Thermal Information table, row "Junction-to-Ambient" (R_θJA). Note the PCB it is quoted on (JEDEC 1s or 2s2p). | |
| Thermal resistance, junction to case | θ_JC | C/W | typ, max | Thermal Characteristics table, row "Junction-to-Case" (R_θJC). For power packages use the tab / bottom value. | |
| Maximum junction temperature | T_J(max) | C | max | Absolute Maximum Ratings table, row "Junction Temperature" or "Operating Junction Temperature" (T_J). | |
| Power dissipation | P_D | W | max | Absolute Maximum Ratings, row "Power Dissipation" (P_D or P_tot) at T_A = 25 °C. If only a derating curve exists read its 25 °C value. | |
| Thermal shutdown temperature | T_SD | C | typ | Electrical Characteristics, row "Thermal Shutdown". | |
| Pin count | N_pins | typ | Package / Pin Configuration drawing on page 1 or 2. Count every terminal including the exposed pad. |
Regulator · Charge pump (regulator.chargepump → device reg chargepump)
Simulation pins: in, out, gnd.
| Field | Symbol | Unit | Columns | Sets | Where to find it in the datasheet |
|---|---|---|---|---|---|
| Mode (−1 = inverter, 2 = doubler) * | mode | typ | Title and Typical Application drawing: "voltage inverter" (−1) or "voltage doubler" (2). | ||
| Input voltage range * | V_IN | V | min, max | Recommended Operating Conditions, row "Supply Voltage". | |
| Output resistance * | R_OUT | Ohm | typ, max | Electrical Characteristics, row "Output Resistance" (R_O) with the recommended pump capacitors (for example 10 µF). | |
| Oscillator frequency | f_OSC | Hz | typ | Electrical Characteristics, row "Oscillator Frequency" (the pump runs at half of it on some parts). | |
| Supply current | I_Q | A | typ, max | Electrical Characteristics, row "Supply Current" with no load. | |
| Maximum output current | I_OUT | A | max | Recommended Operating Conditions, or Electrical Characteristics, row "Output Current". | |
| Power efficiency | η_P | typ | Electrical Characteristics, row "Power Efficiency" at the stated load. | ||
| Recommended pump capacitor | C_1, C_2 | F | typ | Typical Application drawing, values of C1 (flying) and C2 (reservoir). | |
| Thermal resistance, junction to ambient | θ_JA | C/W | typ, max | Thermal Characteristics / Thermal Information table, row "Junction-to-Ambient" (R_θJA). Note the PCB it is quoted on (JEDEC 1s or 2s2p). | |
| Thermal resistance, junction to case | θ_JC | C/W | typ, max | Thermal Characteristics table, row "Junction-to-Case" (R_θJC). For power packages use the tab / bottom value. | |
| Maximum junction temperature | T_J(max) | C | max | Absolute Maximum Ratings table, row "Junction Temperature" or "Operating Junction Temperature" (T_J). | |
| Power dissipation | P_D | W | max | Absolute Maximum Ratings, row "Power Dissipation" (P_D or P_tot) at T_A = 25 °C. If only a derating curve exists read its 25 °C value. | |
| Pin count | N_pins | typ | Package / Pin Configuration drawing on page 1 or 2. Count every terminal including the exposed pad. |
Regulator · LDO (regulator.ldo → device reg ldo)
Simulation pins: in, out, gnd, en. Curves: PSRR vs frequency, Dropout vs load current, Ground current vs load current, Output voltage vs load current (load regulation), Output voltage vs temperature, Dropout voltage vs temperature, Output noise density vs frequency, Output impedance vs frequency.
| Field | Symbol | Unit | Columns | Sets | Where to find it in the datasheet |
|---|---|---|---|---|---|
| Output voltage * | V_OUT | V | min, typ, max | Electrical Characteristics table, row "Output Voltage", at the nominal load current (pick the row for your fixed-voltage option). | |
| Dropout voltage * | V_DO | V | typ, max | Electrical Characteristics, row "Dropout Voltage" at I_OUT max. If only a curve exists read "Dropout vs Load Current" at your maximum load. | |
| Maximum output current * | I_OUT(max) | A | max | Recommended Operating Conditions, row "Output Current" (not Absolute Maximum Ratings). | |
| Current limit | I_LIM | A | min, typ | Electrical Characteristics, row "Current Limit" or "Short Circuit Current". | |
| Quiescent current * | I_Q | A | typ, max | Electrical Characteristics, row "Quiescent Current" or "Ground Pin Current" with no load, EN high. | |
| Input voltage range * | V_IN | V | min, max | Recommended Operating Conditions, row "Input Voltage". | |
| Line regulation | ΔV_OUT/ΔV_IN | %/V | typ, max | Electrical Characteristics, row "Line Regulation". Convert mV/V to %/V by dividing by V_OUT. | |
| Load regulation | ΔV_OUT | % | typ, max | Electrical Characteristics, row "Load Regulation", 1 mA to I_OUT max. | |
| Shutdown current | I_SD | A | typ, max | Electrical Characteristics, row "Shutdown Current" or "Standby Current" with EN low. | |
| Ground current at full load | I_GND | A | typ, max | Electrical Characteristics, row "Ground Pin Current" at the stated load. | |
| Output voltage accuracy | ΔV_OUT | % | typ, max | Electrical Characteristics, row "Output Voltage Accuracy" or "Tolerance" over line, load and temperature. | |
| Output voltage temperature coefficient | TC | ppm/C | typ | Electrical Characteristics, row "Output Voltage Temperature Coefficient". | |
| Short-circuit current | I_SC | A | typ | Electrical Characteristics, row "Short-Circuit Current" (foldback parts list a lower value than the limit). | |
| Enable threshold, high | V_EN(H) | V | min | Electrical Characteristics, row "EN Input High Voltage". | |
| Enable threshold, low | V_EN(L) | V | max | Electrical Characteristics, row "EN Input Low Voltage". | |
| Start-up time | t_on | s | typ, max | Electrical Characteristics, row "Turn-On Time" or "Start-Up Time" at the stated C_OUT. | |
| Input undervoltage lockout | V_UVLO | V | typ | Electrical Characteristics, row "UVLO Threshold" (rising). | |
| PSRR at 1 kHz | PSRR | dB | typ | Graph "PSRR vs Frequency" (or row "Ripple Rejection") at 1 kHz. Add more points as a curve for accuracy. | |
| Output noise | V_N | V | typ | Electrical Characteristics, row "Output Noise Voltage" (e_n or V_N, µVrms). Note the bandwidth it is quoted over. | |
| Minimum output capacitor * | C_OUT(min) | F | min | Application Information, "Output Capacitor". Ceramic is fine when no minimum ESR is given. | |
| Output capacitor ESR, minimum | ESR_min | Ohm | min | Graph "Stability Region vs ESR", if present. Leave empty for ceramic-stable parts. | |
| Output capacitor ESR, maximum | ESR_max | Ohm | max | Same graph, upper edge of the stable region. | |
| Thermal resistance, junction to ambient | θ_JA | C/W | typ, max | Thermal Characteristics / Thermal Information table, row "Junction-to-Ambient" (R_θJA). Note the PCB it is quoted on (JEDEC 1s or 2s2p). | |
| Thermal resistance, junction to case | θ_JC | C/W | typ, max | Thermal Characteristics table, row "Junction-to-Case" (R_θJC). For power packages use the tab / bottom value. | |
| Maximum junction temperature | T_J(max) | C | max | Absolute Maximum Ratings or Recommended Operating Conditions, row "Junction Temperature". Also note the thermal shutdown threshold. | |
| Power dissipation | P_D | W | max | Absolute Maximum Ratings, row "Power Dissipation" (P_D or P_tot) at T_A = 25 °C. If only a derating curve exists read its 25 °C value. | |
| Thermal shutdown temperature | T_SD | C | typ | Electrical Characteristics, row "Thermal Shutdown Temperature". | |
| Thermal shutdown hysteresis | ΔT_SD | C | typ | Electrical Characteristics, row "Thermal Shutdown Hysteresis". | |
| Pin count | N_pins | typ | Package / Pin Configuration drawing on page 1 or 2. Count every terminal including the exposed pad. |
55.17Protection
Protection · ESD / TVS array (protection.esd → device esd)
Simulation pins: io1, io2, gnd. Symbol variants: 2ch, 1ch, 4ch, 2ch_vbus, 4ch_vbus, usblc6.
| Field | Symbol | Unit | Columns | Sets | Where to find it in the datasheet |
|---|---|---|---|---|---|
| Reverse working voltage * | V_RWM | V | max | vrwm | Electrical characteristics, row "Reverse working voltage V_RWM". |
| Breakdown voltage | V_BR | V | min | vbr | Row "Breakdown voltage V_BR" at I_T. |
| Clamping voltage | V_C | V | max | vc | Row "Clamping voltage" at I_PP (8/20 µs). |
| Peak pulse current | I_PP | A | max | ipp | Same row, I_PP. |
| Line capacitance | C_J | F | typ, max | cj | Row "Line capacitance / Junction capacitance" (I/O to GND). |
| Operating temperature range | T_op | C | min, max | Features or Recommended Operating Conditions, row "Operating Temperature Range" (minimum and maximum). | |
| Pin count | N_pins | typ | Package / Pin Configuration drawing on page 1 or 2. Count every terminal including the exposed pad. |
Protection · Fuse (fast / slow / breaker) (protection.fuse → device fuse)
Simulation pins: a, b. Symbol variants: fast, veryfast, slow, breaker, thermal, thermostat. Curves: Time-current curve.
| Field | Symbol | Unit | Columns | Sets | Where to find it in the datasheet |
|---|---|---|---|---|---|
| Rated current * | I_N | A | typ | irated | Ordering table, column "Current Rating" (I_N). |
| Voltage rating | V_N | V | max | vrated | Ordering table, column "Voltage Rating". |
| Cold resistance | R_cold | Ohm | typ | r | Ordering table, column "Cold Resistance" / "Typical DC resistance". Or voltage drop / I_N. |
| Nominal melting I²t | I²t | A2s | typ | i2t | Ordering table, column "Nominal Melting I²t" (A²s). |
| Breaking capacity | I_break | A | min | Ordering table, column "Interrupting Rating" (informational). | |
| Operating temperature range | T_op | C | min, max | Features or Recommended Operating Conditions, row "Operating Temperature Range" (minimum and maximum). | |
| Pin count | N_pins | typ | Package / Pin Configuration drawing on page 1 or 2. Count every terminal including the exposed pad. |
Protection · Gas discharge tube (protection.gdt → device gdt)
Simulation pins: a, b. Symbol variants: 2pin, 3pin.
| Field | Symbol | Unit | Columns | Sets | Where to find it in the datasheet |
|---|---|---|---|---|---|
| DC spark-over voltage * | V_s(DC) | V | min, typ, max | v_spark | Electrical characteristics, "DC spark-over voltage" (100 V/s). |
| Impulse spark-over voltage | V_s(imp) | V | max | Row "Impulse spark-over at 100 V/µs" / "1 kV/µs". Fits k_imp. | |
| Arc voltage | V_arc | V | typ | v_arc | Row "Arc voltage". |
| Capacitance | C | F | max | Row "Capacitance" (pF). | |
| Operating temperature range | T_op | C | min, max | Features or Recommended Operating Conditions, row "Operating Temperature Range" (minimum and maximum). | |
| Pin count | N_pins | typ | Package / Pin Configuration drawing on page 1 or 2. Count every terminal including the exposed pad. |
Protection · Resettable fuse (PPTC) (protection.pptc → device pptc)
Simulation pins: a, b. Curves: Time to trip.
| Field | Symbol | Unit | Columns | Sets | Where to find it in the datasheet |
|---|---|---|---|---|---|
| Hold current * | I_hold | A | typ | ihold | Electrical characteristics, column "I_hold" at 25 °C. |
| Trip current * | I_trip | A | typ | itrip | Electrical characteristics, column "I_trip" at 25 °C. |
| Initial resistance (min) | R_min | Ohm | min | r_min | Column "R_min". |
| Post-trip resistance (max) | R1_max | Ohm | max | r1max | Column "R1max" (1 h after trip). |
| Time to trip | t_trip | s | max | t_trip | Columns "Max time to trip": the time and its current (for example 0.1 s at 8 A). Enter the current in i_ttrip. |
| Current for time to trip | I_t | A | typ | i_ttrip | Same row, the current at which the time to trip is given. |
| Maximum voltage | V_max | V | max | vmax | Column "V_max". |
| Operating temperature range | T_op | C | min, max | Features or Recommended Operating Conditions, row "Operating Temperature Range" (minimum and maximum). | |
| Pin count | N_pins | typ | Package / Pin Configuration drawing on page 1 or 2. Count every terminal including the exposed pad. |
Protection · Varistor (MOV) (protection.mov → device mov)
Simulation pins: a, b.
| Field | Symbol | Unit | Columns | Sets | Where to find it in the datasheet |
|---|---|---|---|---|---|
| Varistor voltage at 1 mA * | V_1mA | V | min, typ, max | v1ma | Ratings table, column "Varistor Voltage V_1mA" (±10 %). |
| Max AC voltage | V_rms | V | max | Column "Max. allowable voltage AC (rms)". | |
| Clamping voltage | V_C | V | max | Column "Max. clamping voltage V_C at I_P". With I_P it fits alpha. | |
| Clamping test current | I_P | A | typ | Same column, the test current I_P. | |
| Energy rating | W_max | J | max | e_max | Column "Energy (10/1000 µs)". |
| Capacitance | C | F | typ | c | Column "Typical capacitance at 1 kHz". |
| Operating temperature range | T_op | C | min, max | Features or Recommended Operating Conditions, row "Operating Temperature Range" (minimum and maximum). | |
| Pin count | N_pins | typ | Package / Pin Configuration drawing on page 1 or 2. Count every terminal including the exposed pad. |
55.18RF
RF · Antenna (rf.antenna → device antenna)
Simulation pins: feed. Symbol variants: mono, dipole, chip, pcb.
| Field | Symbol | Unit | Columns | Sets | Where to find it in the datasheet |
|---|---|---|---|---|---|
| Centre frequency * | f_0 | Hz | typ | f0 | Electrical specifications, "Frequency range" (centre). |
| Impedance | Z | Ohm | typ | r_rad | "Impedance" (50 Ω). |
| VSWR | VSWR | max | "VSWR" (informational). | ||
| Peak gain | G | dBi | typ | "Peak gain" (informational). | |
| Operating temperature range | T_op | C | min, max | Features or Recommended Operating Conditions, row "Operating Temperature Range" (minimum and maximum). |
RF · Attenuator (rf.attenuator → device attenuator)
Simulation pins: IN, OUT, GND.
| Field | Symbol | Unit | Columns | Sets | Where to find it in the datasheet |
|---|---|---|---|---|---|
| Attenuation * | A | dB | typ | atten_db | "Attenuation". |
| Impedance | Z_0 | Ohm | typ | z0 | "Impedance". |
| Operating temperature range | T_op | C | min, max | Features or Recommended Operating Conditions, row "Operating Temperature Range" (minimum and maximum). | |
| Pin count | N_pins | typ | Package / Pin Configuration drawing on page 1 or 2. Count every terminal including the exposed pad. |
RF · Balun (rf.balun → device balun)
Simulation pins: UNBAL, GND, BAL+, BAL−. Symbol variants: 1:1, 1:2, 1:4.
| Field | Symbol | Unit | Columns | Sets | Where to find it in the datasheet |
|---|---|---|---|---|---|
| Impedance ratio * | Z ratio | typ | ratio | "Impedance ratio" (1:1, 1:2, 1:4) → variant. | |
| Frequency range | f | Hz | min, max | "Frequency range" (informational). | |
| Operating temperature range | T_op | C | min, max | Features or Recommended Operating Conditions, row "Operating Temperature Range" (minimum and maximum). | |
| Pin count | N_pins | typ | Package / Pin Configuration drawing on page 1 or 2. Count every terminal including the exposed pad. |
RF · RF amplifier (rf.rfamp → device rfamp)
Simulation pins: IN, OUT, VCC, GND.
| Field | Symbol | Unit | Columns | Sets | Where to find it in the datasheet |
|---|---|---|---|---|---|
| Gain * | G | dB | typ | gain_db | Electrical characteristics, "Small-signal gain" at your frequency. |
| Bandwidth | f_3dB | Hz | typ | f3db | "Frequency range" upper limit. |
| Output P1dB | P1dB | dBm | typ | p1db | "Output power at 1 dB compression". |
| Noise figure | NF | dB | typ | nf_db | "Noise figure". |
| Supply current | I_CC | A | typ | icc | "Device current". |
| Operating temperature range | T_op | C | min, max | Features or Recommended Operating Conditions, row "Operating Temperature Range" (minimum and maximum). | |
| Pin count | N_pins | typ | Package / Pin Configuration drawing on page 1 or 2. Count every terminal including the exposed pad. |
RF · SAW / band-pass filter (rf.saw → device saw)
Simulation pins: IN, OUT, GND.
| Field | Symbol | Unit | Columns | Sets | Where to find it in the datasheet |
|---|---|---|---|---|---|
| Centre frequency * | f_C | Hz | typ | f0 | Electrical characteristics, "Center frequency". |
| Bandwidth * | BW | Hz | typ | bw | "Pass bandwidth" (−3 dB). |
| Insertion loss | IL | dB | typ, max | il_db | "Insertion loss". |
| Operating temperature range | T_op | C | min, max | Features or Recommended Operating Conditions, row "Operating Temperature Range" (minimum and maximum). | |
| Pin count | N_pins | typ | Package / Pin Configuration drawing on page 1 or 2. Count every terminal including the exposed pad. |
55.19Sensors
Sensors · Analog-output sensor (sensors.asensor → device asensor)
Simulation pins: VCC, GND, OUT. Symbol variants: temp, pressure, humidity, light, accel, generic.
| Field | Symbol | Unit | Columns | Sets | Where to find it in the datasheet |
|---|---|---|---|---|---|
| Sensitivity * | S | V/unit | typ | sens | Electrical characteristics, "Sensitivity" / "Scale factor" (LM35: 10 mV/°C). |
| Output at x = 0 | V_0 | V | typ | offset | "Offset" / "Output at 0 °C" (TMP36: 0.5 V. MCP9700: 0.5 V). |
| Ratiometric output | ratiometric | 0/1 | typ | ratiometric | Notes: "ratiometric to V_S" → 1 (pressure sensors, Hall linear). |
| Supply current | I_Q | A | typ, max | icc | "Quiescent current". |
| Measurement range | range | unit | min, max | "Measurement range" (informational). | |
| Operating temperature range | T_op | C | min, max | Features or Recommended Operating Conditions, row "Operating Temperature Range" (minimum and maximum). | |
| Pin count | N_pins | typ | Package / Pin Configuration drawing on page 1 or 2. Count every terminal including the exposed pad. |
Sensors · Bridge sensor / load cell (sensors.bridge_sensor → device bridge_sensor)
Simulation pins: exc+, exc−, out+, out−. Symbol variants: loadcell, pressure.
| Field | Symbol | Unit | Columns | Sets | Where to find it in the datasheet |
|---|---|---|---|---|---|
| Rated output * | RO | mV/V | typ | sens | Specifications, "Rated output" / "Sensitivity" at full scale. |
| Bridge resistance | R_in | Ohm | typ | r_bridge | "Input resistance" / "Output resistance". |
| Zero balance | ZB | mV/V | typ | zero | "Zero balance" / "Zero output". |
| Capacity | FS | unit | typ | "Rated capacity" (informational: x = load / capacity). | |
| Operating temperature range | T_op | C | min, max | Features or Recommended Operating Conditions, row "Operating Temperature Range" (minimum and maximum). | |
| Pin count | N_pins | typ | Package / Pin Configuration drawing on page 1 or 2. Count every terminal including the exposed pad. |
Sensors · Gas sensor (MQ series) (sensors.gas → device gas)
Simulation pins: h1, h2, a, b. Symbol variants: mq2, mq135, mq7.
| Field | Symbol | Unit | Columns | Sets | Where to find it in the datasheet |
|---|---|---|---|---|---|
| Heater resistance * | R_H | Ohm | typ | r_h | Standard work condition table, "Heater resistance R_H". |
| Sensing resistance in reference gas | R_S | Ohm | min, max | r0 | Characteristics, "Sensing resistance" in the stated gas / concentration. |
| Concentration slope | α | typ | k | Sensitivity graph log(Rs/R0) vs log(ppm): the slope. | |
| Operating temperature range | T_op | C | min, max | Features or Recommended Operating Conditions, row "Operating Temperature Range" (minimum and maximum). | |
| Pin count | N_pins | typ | Package / Pin Configuration drawing on page 1 or 2. Count every terminal including the exposed pad. |
Sensors · Hall current sensor (sensors.isense_hall → device isense_hall)
Simulation pins: ip+, ip−, vcc, gnd, out, filt.
| Field | Symbol | Unit | Columns | Sets | Where to find it in the datasheet |
|---|---|---|---|---|---|
| Sensitivity * | Sens | V/A | typ | sens | Electrical characteristics, "Sensitivity" (mV/A) for your current range option. |
| Primary conductor resistance | R_IP | Ohm | typ | r_ip | "Internal conductor resistance". |
| Bandwidth | BW | Hz | typ | bw | "Bandwidth" (−3 dB) or rise time. |
| Zero-current output | V_IOUT(Q) | V | typ | vq | "Zero current output voltage" (V_CC × 0.5 ratiometric). |
| Operating temperature range | T_op | C | min, max | Features or Recommended Operating Conditions, row "Operating Temperature Range" (minimum and maximum). | |
| Pin count | N_pins | typ | Package / Pin Configuration drawing on page 1 or 2. Count every terminal including the exposed pad. |
Sensors · Hall sensor (sensors.hall → device hall)
Simulation pins: VCC, GND, OUT. Symbol variants: switch, latch, omni, linear.
| Field | Symbol | Unit | Columns | Sets | Where to find it in the datasheet |
|---|---|---|---|---|---|
| Operate point * | B_OP | mT | min, typ, max | bop | Magnetic characteristics, "Operate point B_OP" (G → /10 for mT). |
| Release point | B_RP | mT | min, typ, max | brp | "Release point B_RP". |
| Sensitivity (linear) | Sens | mV/mT | min, typ, max | sens | Linear parts: "Sensitivity" (mV/G × 10 → mV/mT). |
| Supply current | I_CC | A | typ, max | icc | "Supply current". |
| Operating temperature range | T_op | C | min, max | Features or Recommended Operating Conditions, row "Operating Temperature Range" (minimum and maximum). | |
| Pin count | N_pins | typ | Package / Pin Configuration drawing on page 1 or 2. Count every terminal including the exposed pad. |
Sensors · NTC thermistor (sensors.ntc → device ntc)
Simulation pins: a, b. Symbol variants: sensor, icl. Curves: R/T table.
| Field | Symbol | Unit | Columns | Sets | Where to find it in the datasheet |
|---|---|---|---|---|---|
| Resistance at 25 °C * | R25 | Ohm | typ | r25 | Part-number table, column "R25" (for example 103 = 10 kΩ). |
| B-constant * | B25/50 | K | typ | beta | Column "B25/50" or "B25/85" (state which pair in the notes). |
| Dissipation constant | δ | W/K | typ | dissipation | Characteristics, row "Dissipation factor" (mW/°C in still air). |
| Thermal time constant | τ | s | typ | tau | Characteristics, row "Thermal time constant" (s in still air). |
| Max power | P_max | W | max | pmax | Absolute maximum, "Rated power" / "Max power at 25 °C". |
| Max steady current (ICL) | I_max | A | max | Inrush limiters: "Max. steady state current" (informational). | |
| Resistance tolerance at 25 °C | ±tol | % | typ | Electrical Specifications, row "R25 Tolerance" (F = 1 %, J = 5 %). | |
| B-value tolerance | ±tol_B | % | typ | Electrical Specifications, row "B Constant Tolerance". | |
| Dissipation constant | δ | W/C | typ | Electrical Specifications, row "Dissipation Constant" (mW/°C in still air). | |
| Thermal time constant | τ | s | typ | Electrical Specifications, row "Thermal Time Constant". | |
| Maximum operating temperature | T_max | C | max | Electrical Specifications, row "Operating Temperature Range" (upper limit). | |
| Operating temperature range | T_op | C | min, max | Features or Recommended Operating Conditions, row "Operating Temperature Range" (minimum and maximum). | |
| Pin count | N_pins | typ | Package / Pin Configuration drawing on page 1 or 2. Count every terminal including the exposed pad. |
Sensors · Photoresistor (LDR) (sensors.ldr → device ldr)
Simulation pins: a, b.
| Field | Symbol | Unit | Columns | Sets | Where to find it in the datasheet |
|---|---|---|---|---|---|
| Light resistance at 10 lx * | R10 | Ohm | min, max | r10 | Characteristics table, column "Light resistance (10 lux)" (often a min–max range). |
| Gamma | γ | typ | gamma | Column "γ (100/10)" or "γ". | |
| Dark resistance | R_dark | Ohm | min | r_dark | Column "Dark resistance" (min, after 10 s). |
| Response time, rise | t_r | s | typ | t_rise | Column "Response time rise / decay" (ms). |
| Response time, decay | t_f | s | typ | t_fall | Same column, decay value. |
| Operating temperature range | T_op | C | min, max | Features or Recommended Operating Conditions, row "Operating Temperature Range" (minimum and maximum). | |
| Pin count | N_pins | typ | Package / Pin Configuration drawing on page 1 or 2. Count every terminal including the exposed pad. |
Sensors · PIR motion module (sensors.pir → device pir)
Simulation pins: VCC, OUT, GND.
| Field | Symbol | Unit | Columns | Sets | Where to find it in the datasheet |
|---|---|---|---|---|---|
| Output hold time | t_hold | s | typ | t_hold | Module spec, "Delay time" (trimmer range). |
| Quiescent current | I_Q | A | typ | icc | "Static current". |
| Operating temperature range | T_op | C | min, max | Features or Recommended Operating Conditions, row "Operating Temperature Range" (minimum and maximum). |
Sensors · PTC thermistor (sensors.ptc → device ptc)
Simulation pins: a, b. Symbol variants: switching, linear.
| Field | Symbol | Unit | Columns | Sets | Where to find it in the datasheet |
|---|---|---|---|---|---|
| Resistance at 25 °C * | R25 | Ohm | typ | r25 | Ordering table, column "R25" / "R_N". |
| Reference (switching) temperature | T_ref | C | typ | t_c | Ceramic PTC: "Reference temperature T_ref" / "Curie temperature". |
| Temperature coefficient | α | 1/K | typ | alpha | Silicon KTY: "Temperature coefficient α" (%/K → /100). |
| Operating temperature range | T_op | C | min, max | Features or Recommended Operating Conditions, row "Operating Temperature Range" (minimum and maximum). | |
| Dissipation constant | δ | W/K | typ | dissipation | Characteristics, "Dissipation factor". |
| Pin count | N_pins | typ | Package / Pin Configuration drawing on page 1 or 2. Count every terminal including the exposed pad. |
Sensors · RTD (Pt100 / Pt1000) (sensors.rtd → device rtd)
Simulation pins: a, b. Symbol variants: pt100, pt1000, ni1000.
| Field | Symbol | Unit | Columns | Sets | Where to find it in the datasheet |
|---|---|---|---|---|---|
| Resistance at 0 °C * | R0 | Ohm | typ | r0 | Ordering table: Pt100 / Pt1000 (R0). |
| Temperature coefficient | α | 1/K | typ | cvd_a | Specification: α = 0.00385 (IEC 60751) or 0.00392. Converted to the CVD coefficients. |
| Tolerance class | class | typ | Class B / A / AA (informational). | ||
| Operating temperature range | T_op | C | min, max | Features or Recommended Operating Conditions, row "Operating Temperature Range" (minimum and maximum). | |
| Self-heating coefficient | δ | W/K | typ | dissipation | Row "Self-heating" (mK/mW → 1/value). |
| Pin count | N_pins | typ | Package / Pin Configuration drawing on page 1 or 2. Count every terminal including the exposed pad. |
Sensors · Strain gauge (sensors.strain → device strain)
Simulation pins: a, b.
| Field | Symbol | Unit | Columns | Sets | Where to find it in the datasheet |
|---|---|---|---|---|---|
| Nominal resistance * | R_0 | Ohm | typ | r0 | Specification, "Resistance" (120 / 350 / 1000 Ω). |
| Gauge factor * | k | typ | gf | Specification, "Gauge factor". | |
| Operating temperature range | T_op | C | min, max | Features or Recommended Operating Conditions, row "Operating Temperature Range" (minimum and maximum). | |
| Pin count | N_pins | typ | Package / Pin Configuration drawing on page 1 or 2. Count every terminal including the exposed pad. |
Sensors · Thermocouple (sensors.tcouple → device tcouple)
Simulation pins: +, −. Symbol variants: K, J, T, E, N.
| Field | Symbol | Unit | Columns | Sets | Where to find it in the datasheet |
|---|---|---|---|---|---|
| Thermocouple type * | type | typ | Type letter (K, J, T, E, N) → variant. | ||
| Loop resistance | R_loop | Ohm | typ | r | Wire table: Ω/m × length (both legs). |
| Operating temperature range | T_op | C | min, max | Features or Recommended Operating Conditions, row "Operating Temperature Range" (minimum and maximum). | |
| Max temperature | T_max | C | max | Specifications: "Temperature range" (informational). |
Sensors · Touch sensor IC (sensors.touch → device touch)
Simulation pins: Q, VSS, I, AHLB, VDD, TOG.
| Field | Symbol | Unit | Columns | Sets | Where to find it in the datasheet |
|---|---|---|---|---|---|
| Response time | t_R | s | typ | t_resp | "Response time" (fast / low-power mode). |
| Operating current | I_DD | A | typ | "Operating current". | |
| Operating temperature range | T_op | C | min, max | Features or Recommended Operating Conditions, row "Operating Temperature Range" (minimum and maximum). | |
| Pin count | N_pins | typ | Package / Pin Configuration drawing on page 1 or 2. Count every terminal including the exposed pad. |
Sensors · Ultrasonic ranger (sensors.ultrasonic → device ultrasonic)
Simulation pins: VCC, TRIG, ECHO, GND.
| Field | Symbol | Unit | Columns | Sets | Where to find it in the datasheet |
|---|---|---|---|---|---|
| Range | d | m | min, max | Module spec, "Ranging distance" (informational). | |
| Operating current | I | A | typ | icc | "Working current". |
| Operating temperature range | T_op | C | min, max | Features or Recommended Operating Conditions, row "Operating Temperature Range" (minimum and maximum). |
55.20Sources
Sources · Solar cell (sources.solar → device solar)
Simulation pins: +, −.
| Field | Symbol | Unit | Columns | Sets | Where to find it in the datasheet |
|---|---|---|---|---|---|
| Short-circuit current * | I_SC | A | typ | isc | Electrical data at STC (1000 W/m²), "I_sc". |
| Open-circuit voltage * | V_OC | V | typ | voc | Electrical data at STC, "V_oc" (enter the panel value and the cell count). |
| Cells in series | N_s | typ | cells | Mechanical data, "Cells". | |
| Max power | P_mpp | W | typ | "P_max", with V_mpp / I_mpp (fit n and rs). | |
| Operating temperature range | T_op | C | min, max | Features or Recommended Operating Conditions, row "Operating Temperature Range" (minimum and maximum). | |
| Pin count | N_pins | typ | Package / Pin Configuration drawing on page 1 or 2. Count every terminal including the exposed pad. |
55.21Timing
Timing · 556 dual timer (timing.timer556 → device timer556)
Simulation pins: DIS1, THR1, CTRL1, RST1, OUT1, TRIG1, GND, TRIG2, OUT2, RST2, CTRL2, THR2, DIS2, VCC.
| Field | Symbol | Unit | Columns | Sets | Where to find it in the datasheet |
|---|---|---|---|---|---|
| Technology | family | typ | family | NE556 (bipolar) or TLC556 / ICM7556 (CMOS) → family. | |
| Supply current | I_CC | A | typ, max | "Supply current" (both timers). | |
| Operating temperature range | T_op | C | min, max | Features or Recommended Operating Conditions, row "Operating Temperature Range" (minimum and maximum). | |
| Pin count | N_pins | typ | Package / Pin Configuration drawing on page 1 or 2. Count every terminal including the exposed pad. |
Timing · Ceramic resonator (timing.resonator → device resonator)
Simulation pins: in, gnd, out. Symbol variants: 3pin, 2pin.
| Field | Symbol | Unit | Columns | Sets | Where to find it in the datasheet |
|---|---|---|---|---|---|
| Oscillation frequency * | f_osc | Hz | typ | freq | Ordering table, "Oscillating frequency". |
| Built-in load capacitance | C_L1, C_L2 | F | typ | cl_int | Ordering table, "Built-in load capacitance" (each side). |
| Resonant resistance | R_1 | Ohm | max | rm | Equivalent circuit constants table, "R1". |
| Frequency tolerance | Δf/f | % | max | tol | "Initial tolerance". |
| Operating temperature range | T_op | C | min, max | Features or Recommended Operating Conditions, row "Operating Temperature Range" (minimum and maximum). | |
| Pin count | N_pins | typ | Package / Pin Configuration drawing on page 1 or 2. Count every terminal including the exposed pad. |
Timing · Crystal (timing.xtal → device xtal)
Simulation pins: x1, x2. Symbol variants: 2pin, 4pin.
| Field | Symbol | Unit | Columns | Sets | Where to find it in the datasheet |
|---|---|---|---|---|---|
| Nominal frequency * | f_0 | Hz | typ | freq | Ordering code / Electrical specifications, "Nominal frequency". |
| Load capacitance * | C_L | F | typ | cl | Electrical specifications, "Load capacitance C_L" (ordering option, for example 12 / 18 / 20 pF). |
| Equivalent series resistance | ESR | Ohm | max | esr | Electrical specifications, "ESR / Series resistance R1" (max). |
| Shunt capacitance | C_0 | F | max | c0 | Electrical specifications, "Shunt capacitance C0" (max). |
| Motional capacitance | C_1 | F | typ | cm | "Motional capacitance C1" (fF), often only in the extended table. |
| Frequency tolerance | Δf/f | ppm | max | ppm | "Frequency tolerance at 25 °C". |
| Drive level | DL | W | max | drive_max | "Drive level" (µW). |
| Aging | Δf/f | ppm | max | Electrical Specifications, row "Aging (first year)". | |
| Frequency stability over temperature | Δf/f | ppm | max | Electrical Specifications, row "Frequency Stability over Temperature". | |
| Pullability | S | ppm/F | typ | Electrical Specifications, row "Pullability" (ppm per pF: 20 ppm/pF is 2e13 per F). | |
| Operating temperature range | T_op | C | min, max | Features or Recommended Operating Conditions, row "Operating Temperature Range" (minimum and maximum). | |
| Pin count | N_pins | typ | Package / Pin Configuration drawing on page 1 or 2. Count every terminal including the exposed pad. |
Timing · Oscillator module (timing.xo → device xo)
Simulation pins: EN, GND, OUT, VDD. Symbol variants: xo, tcxo, vcxo, mems.
| Field | Symbol | Unit | Columns | Sets | Where to find it in the datasheet |
|---|---|---|---|---|---|
| Output frequency * | f_out | Hz | typ | freq | Ordering code, "Frequency". |
| Supply voltage | V_DD | V | min, typ, max | vdd_min | Electrical specifications, "Supply voltage". |
| Supply current | I_DD | A | max | idd | Electrical specifications, "Supply current" at your frequency, no load. |
| Rise / fall time | t_r | s | max | tr | "Rise / fall time" (10–90 %). |
| Start-up time | t_start | s | max | startup | "Start-up time". |
| Frequency stability | Δf/f | ppm | max | "Frequency stability" over temperature (informational). | |
| Pull range (VCXO) | APR | ppm | typ | pull | VCXO: "Absolute pull range". |
| Operating temperature range | T_op | C | min, max | Features or Recommended Operating Conditions, row "Operating Temperature Range" (minimum and maximum). | |
| Pin count | N_pins | typ | Package / Pin Configuration drawing on page 1 or 2. Count every terminal including the exposed pad. |
Timing · PLL / VCO (timing.pll → device vco)
Simulation pins: ref, fb, out, gnd.
| Field | Symbol | Unit | Columns | Sets | Where to find it in the datasheet |
|---|---|---|---|---|---|
| VCO centre frequency * | f_0 | Hz | min, typ, max | VCO section, row "Center Frequency" or the f vs V_TUNE graph at mid-scale. | |
| VCO gain * | K_VCO | Hz/V | min, typ, max | VCO section, row "Tuning Sensitivity" / "K_VCO" (MHz/V → Hz/V), or the slope of f vs V_TUNE. | |
| VCO minimum frequency | f_MIN | Hz | min | VCO section, row "Frequency Range" (low end). | |
| VCO maximum frequency | f_MAX | Hz | max | VCO section, row "Frequency Range" (high end). | |
| Maximum reference frequency | f_REF | Hz | max | Phase Detector section, row "PFD Frequency" (max). | |
| Charge-pump current | I_CP | A | min, typ, max | Charge Pump section, row "Charge Pump Current" (sink / source, per setting). | |
| Feedback divider range (max N) | N | max | Divider section, row "N Counter Range". | ||
| Lock time | t_LOCK | s | typ | Typical Characteristics or loop-filter application section, "Lock Time" with the stated loop bandwidth. | |
| Phase noise at 10 kHz offset | L(10k) | dBc/Hz | typ | Phase Noise graph or table: value at 10 kHz offset for the stated carrier. | |
| Output high level | V_OH | V | typ | Output section, row "Output High Voltage" (CMOS outputs: V_DD). | |
| Thermal resistance, junction to ambient | θ_JA | C/W | typ, max | Thermal Characteristics / Thermal Information table, row "Junction-to-Ambient" (R_θJA). Note the PCB it is quoted on (JEDEC 1s or 2s2p). | |
| Thermal resistance, junction to case | θ_JC | C/W | typ, max | Thermal Characteristics table, row "Junction-to-Case" (R_θJC). For power packages use the tab / bottom value. | |
| Maximum junction temperature | T_J(max) | C | max | Absolute Maximum Ratings table, row "Junction Temperature" or "Operating Junction Temperature" (T_J). | |
| Power dissipation | P_D | W | max | Absolute Maximum Ratings, row "Power Dissipation" (P_D or P_tot) at T_A = 25 °C. If only a derating curve exists read its 25 °C value. | |
| Pin count | N_pins | typ | Package / Pin Configuration drawing on page 1 or 2. Count every terminal including the exposed pad. |
55.22Transistors
Transistor · IGBT (transistor.igbt → device igbt)
Simulation pins: c, g, e. Curves: Output characteristic, Transfer characteristic, Saturation voltage vs collector current, Saturation voltage vs junction temperature, Input capacitance vs collector-emitter voltage, Switching energy vs collector current.
| Field | Symbol | Unit | Columns | Sets | Where to find it in the datasheet |
|---|---|---|---|---|---|
| Collector-emitter voltage | V_CES | V | max | Absolute Maximum Ratings, row "Collector-Emitter Voltage" (V_CES). | |
| Continuous collector current | I_C | A | max | Absolute Maximum Ratings, row "Continuous Collector Current" at T_C = 100 °C (more realistic than 25 °C). | |
| Gate threshold voltage * | V_GE(th) | V | min, typ, max | Electrical Characteristics, row "Gate-Emitter Threshold Voltage" (V_GE(th)) at I_C = 250 µA..1 mA, V_CE = V_GE. | |
| Collector-emitter saturation voltage * | V_CE(sat) | V | typ, max | Electrical Characteristics, row "Collector-Emitter Saturation Voltage" at the nominal I_C and V_GE = 15 V. Put both in the conditions. | |
| Forward transconductance | g_fs | S | typ | Electrical Characteristics, row "Transconductance" (g_fs), if given. | |
| Input capacitance | C_ies | F | typ | Dynamic Characteristics, row "Input Capacitance" (C_ies). | |
| Total gate charge | Q_G | C | typ | Dynamic Characteristics, row "Gate Charge Total" (Q_G) at V_GE = 15 V. | |
| Turn-on switching energy | E_on | J | typ | Switching Characteristics, row "Turn-On Switching Loss" (E_on) at the stated I_C, V_CE, R_G. | |
| Turn-off switching energy | E_off | J | typ | Switching Characteristics, row "Turn-Off Switching Loss" (E_off). | |
| Maximum gate-emitter voltage | V_GES | V | max | Absolute Maximum Ratings, row "Gate-Emitter Voltage" (V_GES). | |
| Continuous collector current at 100 °C | I_C(100) | A | max | Absolute Maximum Ratings, row "Collector Current" at T_C = 100 °C. | |
| Pulsed collector current | I_CM | A | max | Absolute Maximum Ratings, row "Pulsed Collector Current" (I_CM). | |
| Collector cut-off current | I_CES | A | max | Electrical Characteristics, row "Zero Gate Voltage Collector Current" (I_CES). | |
| Turn-on delay time | t_d(on) | s | typ | Switching Characteristics, row "Turn-On Delay Time". Test conditions in the footnote. | |
| Rise time | t_r | s | typ | Switching Characteristics, row "Rise Time". | |
| Turn-off delay time | t_d(off) | s | typ | Switching Characteristics, row "Turn-Off Delay Time". | |
| Fall time | t_f | s | typ | Switching Characteristics, row "Fall Time" (the current tail may follow, see the note). | |
| Total switching energy | E_ts | J | typ | Switching Characteristics, row "Total Switching Loss" (E_ts = E_on + E_off). | |
| Gate-emitter charge | Q_ge | C | typ | Electrical Characteristics, row "Gate-Emitter Charge". | |
| Gate-collector charge | Q_gc | C | typ | Electrical Characteristics, row "Gate-Collector Charge". | |
| Output capacitance | C_oes | F | typ | Electrical Characteristics, row "Output Capacitance" (C_oes) at V_CE = 25 V. | |
| Reverse transfer capacitance | C_res | F | typ | Electrical Characteristics, row "Reverse Transfer Capacitance" (C_res). | |
| Anti-parallel diode forward voltage | V_F | V | typ, max | Diode Characteristics, row "Diode Forward Voltage". I_F in the conditions. | |
| Anti-parallel diode reverse recovery time | t_rr | s | typ | Diode Characteristics, row "Diode Reverse Recovery Time". | |
| Short-circuit withstand time | t_SC | s | min | Absolute Maximum Ratings or Electrical Characteristics, row "Short-Circuit Withstand Time" at the stated V_GE and V_CC. | |
| Thermal resistance, junction to ambient | θ_JA | C/W | typ, max | Thermal Characteristics / Thermal Information table, row "Junction-to-Ambient" (R_θJA). Note the PCB it is quoted on (JEDEC 1s or 2s2p). | |
| Thermal resistance, junction to case | θ_JC | C/W | typ, max | Thermal Characteristics table, row "Junction-to-Case" (R_θJC). For power packages use the tab / bottom value. | |
| Maximum junction temperature | T_J(max) | C | max | Absolute Maximum Ratings table, row "Junction Temperature" or "Operating Junction Temperature" (T_J). | |
| Power dissipation | P_D | W | max | Absolute Maximum Ratings, row "Power Dissipation" (P_D or P_tot) at T_A = 25 °C. If only a derating curve exists read its 25 °C value. | |
| Pin count | N_pins | typ | Package / Pin Configuration drawing on page 1 or 2. Count every terminal including the exposed pad. |
Transistor · JFET (transistor.jfet → device njf)
Simulation pins: d, g, s. Curves: Transfer characteristic, Output characteristic.
| Field | Symbol | Unit | Columns | Sets | Where to find it in the datasheet |
|---|---|---|---|---|---|
| Gate-source cut-off voltage * | V_GS(off) | V | min, typ, max | Electrical Characteristics, "OFF Characteristics", row "Gate-Source Cutoff Voltage" (V_GS(off)) at V_DS = 15 V, I_D = 10 nA. Keep its sign (negative for N-channel). | |
| Zero-gate-voltage drain current * | I_DSS | A | min, typ, max | Electrical Characteristics, "ON Characteristics", row "Zero-Gate-Voltage Drain Current" (I_DSS) at V_DS = 15 V, V_GS = 0. Positive number. | |
| Forward transfer admittance | |y_fs| | S | min, typ | Small-Signal Characteristics, row "Forward Transfer Admittance" (|y_fs| or g_fs) at 1 kHz. | |
| Drain-source voltage | V_DS | V | max | Absolute Maximum Ratings, row "Drain-Source Voltage". | |
| Gate reverse current | I_GSS | A | max | OFF Characteristics, row "Gate Reverse Current" (I_GSS) at the stated V_GS. | |
| Input capacitance | C_iss | F | typ | Small-Signal Characteristics, row "Input Capacitance" (C_iss). | |
| Reverse transfer capacitance | C_rss | F | typ | Small-Signal Characteristics, row "Reverse Transfer Capacitance" (C_rss). | |
| Drain-source on-resistance | r_ds(on) | Ohm | typ | Electrical Characteristics, row "Static Drain-Source On-Resistance" at V_GS = 0 (small-signal parts). | |
| Gate-source capacitance | C_gs | F | typ | Electrical Characteristics, row "Gate-Source Capacitance". | |
| Gate-drain capacitance | C_gd | F | typ | Electrical Characteristics, row "Gate-Drain Capacitance" (C_rss). | |
| Input voltage noise density | e_n | V/rtHz | typ | Small-Signal Characteristics, row "Equivalent Short-Circuit Input Noise Voltage" (nV/√Hz) at 1 kHz. | |
| Noise figure | NF | dB | typ | Electrical Characteristics, row "Noise Figure" with R_G and f. | |
| Thermal resistance, junction to ambient | θ_JA | C/W | typ, max | Thermal Characteristics / Thermal Information table, row "Junction-to-Ambient" (R_θJA). Note the PCB it is quoted on (JEDEC 1s or 2s2p). | |
| Thermal resistance, junction to case | θ_JC | C/W | typ, max | Thermal Characteristics table, row "Junction-to-Case" (R_θJC). For power packages use the tab / bottom value. | |
| Maximum junction temperature | T_J(max) | C | max | Absolute Maximum Ratings table, row "Junction Temperature" or "Operating Junction Temperature" (T_J). | |
| Power dissipation | P_D | W | max | Absolute Maximum Ratings, row "Power Dissipation" (P_D or P_tot) at T_A = 25 °C. If only a derating curve exists read its 25 °C value. | |
| Pin count | N_pins | typ | Package / Pin Configuration drawing on page 1 or 2. Count every terminal including the exposed pad. |
Transistor · N-channel MOSFET (transistor.nmos → device nmos)
Simulation pins: d, g, s. Symbol variants: enh, power, 4pin, dep. Curves: On-resistance vs gate voltage, Transfer characteristic, Output characteristic, Input capacitance vs drain voltage, Output capacitance vs drain voltage, Reverse transfer capacitance vs drain voltage, On-resistance vs junction temperature, Gate threshold vs junction temperature, Gate voltage vs gate charge, Body diode forward characteristic.
| Field | Symbol | Unit | Columns | Sets | Where to find it in the datasheet |
|---|---|---|---|---|---|
| Drain-source voltage | V_DS | V | max | Absolute Maximum Ratings, row "Drain-Source Voltage" (V_DSS). Store as a positive number. | |
| Continuous drain current | I_D | A | max | Absolute Maximum Ratings, row "Continuous Drain Current" at T_A = 25 °C (the T_C = 25 °C value assumes an ideal heatsink). Positive number. | |
| Gate threshold voltage * | V_GS(th) | V | min, typ, max | Electrical Characteristics, "Static", row "Gate Threshold Voltage" at V_DS = V_GS, I_D = 250 µA. Store as a positive number. | |
| Drain-source on-resistance * | R_DS(on) | Ohm | typ, max | Electrical Characteristics, row "Static Drain-Source On-Resistance" at the V_GS you will drive (for example V_GS = 4.5 V). Put that V_GS in the conditions. | |
| Gate-source voltage | V_GS(max) | V | max | Absolute Maximum Ratings, row "Gate-to-Source Voltage" (±V_GS). | |
| Input capacitance | C_iss | F | typ | Dynamic Characteristics, row "Input Capacitance" (C_iss) at the stated V_DS, 1 MHz. | |
| Output capacitance | C_oss | F | typ | Dynamic Characteristics, row "Output Capacitance" (C_oss). | |
| Reverse transfer capacitance | C_rss | F | typ | Dynamic Characteristics, row "Reverse Transfer Capacitance" (C_rss, the Miller capacitance). | |
| Total gate charge | Q_g | C | typ, max | Dynamic Characteristics, row "Total Gate Charge" (Q_g) at the stated V_GS. Also in the gate-charge graph. | |
| Forward transconductance | g_fs | S | min, typ | Static Characteristics, row "Forward Transconductance" at the stated V_DS and I_D. | |
| Body diode forward voltage | V_SD | V | max | Source-Drain Diode Characteristics, row "Diode Forward Voltage" (V_SD) at I_S. Positive number. | |
| Body diode reverse recovery time | t_rr | s | typ | Source-Drain Diode Characteristics, row "Reverse Recovery Time" (t_rr). | |
| Continuous drain current at 100 °C | I_D(100) | A | max | Absolute Maximum Ratings, row "Continuous Drain Current" at T_C = 100 °C (the first row is usually 25 °C). | |
| Pulsed drain current | I_DM | A | max | Absolute Maximum Ratings, row "Pulsed Drain Current" (I_DM). The pulse width is in the footnote. | |
| On-resistance at low gate drive | R_DS(on) | Ohm | typ, max | Electrical Characteristics, the second R_DS(on) row (for example at V_GS = 4.5 V when the first is at 10 V). Put V_GS and I_D in the conditions. | |
| On-resistance at high temperature | R_DS(on) | Ohm | typ, max | Electrical Characteristics at T_J = 125 or 150 °C, or the normalised R_DS(on) vs temperature graph times the 25 °C value. | |
| Zero-gate-voltage drain current | I_DSS | A | max | Electrical Characteristics, row "Zero Gate Voltage Drain Current" (I_DSS), at V_DS = the rated voltage. | |
| Gate-body leakage current | I_GSS | A | max | Electrical Characteristics, row "Gate-Body Leakage Current" (I_GSS) at V_GS = ±the rated gate voltage. | |
| Gate resistance | R_G | Ohm | typ | Electrical Characteristics, row "Gate Resistance" (R_G) at f = 1 MHz. | |
| Gate-source charge | Q_gs | C | typ | Electrical Characteristics, row "Gate-Source Charge" (Q_gs). | |
| Gate-drain (Miller) charge | Q_gd | C | typ | Electrical Characteristics, row "Gate-Drain Charge" (Q_gd). | |
| Turn-on delay time | t_d(on) | s | typ | Switching Characteristics, row "Turn-On Delay Time". The test circuit and R_G are in the conditions. | |
| Rise time | t_r | s | typ | Switching Characteristics, row "Rise Time". | |
| Turn-off delay time | t_d(off) | s | typ | Switching Characteristics, row "Turn-Off Delay Time". | |
| Fall time | t_f | s | typ | Switching Characteristics, row "Fall Time". | |
| Body diode continuous current | I_S | A | max | Absolute Maximum Ratings or Source-Drain Diode Characteristics, row "Continuous Source Current (Body Diode)". | |
| Body diode reverse recovery charge | Q_rr | C | typ | Source-Drain Diode table, row "Reverse Recovery Charge" (Q_rr), with I_F and di/dt in the footnote. | |
| Single-pulse avalanche energy | E_AS | J | max | Absolute Maximum Ratings, row "Single Pulse Avalanche Energy" (E_AS). The starting T_J, L and I_AS are in the footnote. | |
| Thermal resistance, junction to ambient | θ_JA | C/W | typ, max | Thermal Characteristics / Thermal Information table, row "Junction-to-Ambient" (R_θJA). Note the PCB it is quoted on (JEDEC 1s or 2s2p). | |
| Thermal resistance, junction to case | θ_JC | C/W | typ, max | Thermal Characteristics table, row "Junction-to-Case" (R_θJC). For power packages use the tab / bottom value. | |
| Maximum junction temperature | T_J(max) | C | max | Absolute Maximum Ratings table, row "Junction Temperature" or "Operating Junction Temperature" (T_J). | |
| Power dissipation | P_D | W | max | Absolute Maximum Ratings, row "Power Dissipation" (P_D or P_tot) at T_A = 25 °C. If only a derating curve exists read its 25 °C value. | |
| Pin count | N_pins | typ | Package / Pin Configuration drawing on page 1 or 2. Count every terminal including the exposed pad. |
Transistor · NPN BJT (transistor.npn → device npn)
Simulation pins: c, b, e. Curves: DC current gain vs collector current, Base-emitter voltage vs collector current, Collector-emitter saturation vs current, Transition frequency vs collector current, Output capacitance vs collector-base voltage.
| Field | Symbol | Unit | Columns | Sets | Where to find it in the datasheet |
|---|---|---|---|---|---|
| DC current gain * | h_FE | min, typ, max | Electrical Characteristics, "ON Characteristics", row "DC Current Gain" (h_FE) at the I_C / V_CE closest to your circuit (for example I_C = 10 mA, V_CE = 1 V). | ||
| Collector-emitter voltage | V_CEO | V | max | Absolute Maximum Ratings, row "Collector-Emitter Voltage" (V_CEO, base open). Store as a positive number. | |
| Continuous collector current | I_C | A | max | Absolute Maximum Ratings, row "Collector Current - Continuous" (I_C). Store as a positive number. | |
| Collector-emitter saturation voltage | V_CE(sat) | V | typ, max | ON Characteristics, row "Collector-Emitter Saturation Voltage" at I_C / I_B = 10. Store as a positive number. | |
| Base-emitter voltage | V_BE(on) | V | min, typ, max | ON Characteristics, row "Base-Emitter On Voltage" V_BE(on) (or V_BE(sat)) at the stated I_C. Store as a positive number. | |
| Transition frequency | f_T | Hz | min, typ | Small-Signal Characteristics, row "Current-Gain-Bandwidth Product" (f_T). | |
| Output capacitance | C_obo | F | max | Small-Signal Characteristics, row "Output Capacitance" (C_obo, C_CB at V_CB = 5 V, 1 MHz). | |
| Input capacitance | C_ibo | F | max | Small-Signal Characteristics, row "Input Capacitance" (C_ibo, C_EB at V_EB = 0.5 V, 1 MHz). | |
| Early voltage (model) | V_AF | V | typ | Rarely listed: extrapolate the I_C vs V_CE output curves back to I_C = 0. Typical 50 to 150 V for small-signal parts. | |
| Turn-on time (delay + rise) | t_d + t_r | s | max | Switching Characteristics, rows "Delay Time" and "Rise Time". Add them. | |
| Turn-off time (storage + fall) | t_s + t_f | s | max | Switching Characteristics, rows "Storage Time" and "Fall Time". Add them. | |
| Collector-base voltage | V_CBO | V | max | Absolute Maximum Ratings, row "Collector-Base Voltage" (V_CBO). | |
| Emitter-base voltage | V_EBO | V | max | Absolute Maximum Ratings, row "Emitter-Base Voltage" (V_EBO). | |
| Peak collector current | I_CM | A | max | Absolute Maximum Ratings, row "Peak Collector Current" (I_CM), with the pulse width in the footnote. | |
| Collector cut-off current | I_CBO | A | max | Electrical Characteristics, row "Collector Cut-Off Current" (I_CBO). | |
| Emitter cut-off current | I_EBO | A | max | Electrical Characteristics, row "Emitter Cut-Off Current" (I_EBO). | |
| Base-emitter saturation voltage | V_BE(sat) | V | typ, max | Electrical Characteristics, row "Base-Emitter Saturation Voltage". I_C and I_B (usually a ratio of 10) in the conditions. | |
| Storage time | t_s | s | max | Switching Characteristics, row "Storage Time". | |
| Noise figure | NF | dB | typ | Electrical Characteristics, row "Noise Figure" with source resistance and f. | |
| Thermal resistance, junction to ambient | θ_JA | C/W | typ, max | Thermal Characteristics / Thermal Information table, row "Junction-to-Ambient" (R_θJA). Note the PCB it is quoted on (JEDEC 1s or 2s2p). | |
| Thermal resistance, junction to case | θ_JC | C/W | typ, max | Thermal Characteristics table, row "Junction-to-Case" (R_θJC). For power packages use the tab / bottom value. | |
| Maximum junction temperature | T_J(max) | C | max | Absolute Maximum Ratings table, row "Junction Temperature" or "Operating Junction Temperature" (T_J). | |
| Power dissipation | P_D | W | max | Absolute Maximum Ratings, row "Power Dissipation" (P_D or P_tot) at T_A = 25 °C. If only a derating curve exists read its 25 °C value. | |
| Pin count | N_pins | typ | Package / Pin Configuration drawing on page 1 or 2. Count every terminal including the exposed pad. |
Transistor · P-channel MOSFET (transistor.pmos → device pmos)
Simulation pins: d, g, s. Symbol variants: enh, power, 4pin, dep. Curves: On-resistance vs gate voltage, Output characteristic, Input capacitance vs drain voltage, Output capacitance vs drain voltage, Reverse transfer capacitance vs drain voltage, On-resistance vs junction temperature, Gate threshold vs junction temperature, Gate voltage vs gate charge, Body diode forward characteristic, Transfer characteristic.
| Field | Symbol | Unit | Columns | Sets | Where to find it in the datasheet |
|---|---|---|---|---|---|
| Drain-source voltage | V_DS | V | max | Absolute Maximum Ratings, row "Drain-Source Voltage" (V_DSS). Store as a positive number. | |
| Continuous drain current | I_D | A | max | Absolute Maximum Ratings, row "Continuous Drain Current" at T_A = 25 °C (the T_C = 25 °C value assumes an ideal heatsink). Positive number. | |
| Gate threshold voltage * | V_GS(th) | V | min, typ, max | Electrical Characteristics, "Static", row "Gate Threshold Voltage" at V_DS = V_GS, I_D = −250 µA. Store as a positive number. | |
| Drain-source on-resistance * | R_DS(on) | Ohm | typ, max | Electrical Characteristics, row "Static Drain-Source On-Resistance" at the V_GS you will drive (for example V_GS = −4.5 V). Put that V_GS in the conditions. | |
| Gate-source voltage | V_GS(max) | V | max | Absolute Maximum Ratings, row "Gate-to-Source Voltage" (±V_GS). | |
| Input capacitance | C_iss | F | typ | Dynamic Characteristics, row "Input Capacitance" (C_iss) at the stated V_DS, 1 MHz. | |
| Output capacitance | C_oss | F | typ | Dynamic Characteristics, row "Output Capacitance" (C_oss). | |
| Reverse transfer capacitance | C_rss | F | typ | Dynamic Characteristics, row "Reverse Transfer Capacitance" (C_rss, the Miller capacitance). | |
| Total gate charge | Q_g | C | typ, max | Dynamic Characteristics, row "Total Gate Charge" (Q_g) at the stated V_GS. Also in the gate-charge graph. | |
| Forward transconductance | g_fs | S | min, typ | Static Characteristics, row "Forward Transconductance" at the stated V_DS and I_D. | |
| Body diode forward voltage | V_SD | V | max | Source-Drain Diode Characteristics, row "Diode Forward Voltage" (V_SD) at I_S. Positive number. | |
| Body diode reverse recovery time | t_rr | s | typ | Source-Drain Diode Characteristics, row "Reverse Recovery Time" (t_rr). | |
| Continuous drain current at 100 °C | I_D(100) | A | max | Absolute Maximum Ratings, row "Continuous Drain Current" at T_C = 100 °C (the first row is usually 25 °C). | |
| Pulsed drain current | I_DM | A | max | Absolute Maximum Ratings, row "Pulsed Drain Current" (I_DM). The pulse width is in the footnote. | |
| On-resistance at low gate drive | R_DS(on) | Ohm | typ, max | Electrical Characteristics, the second R_DS(on) row (for example at V_GS = 4.5 V when the first is at 10 V). Put V_GS and I_D in the conditions. | |
| On-resistance at high temperature | R_DS(on) | Ohm | typ, max | Electrical Characteristics at T_J = 125 or 150 °C, or the normalised R_DS(on) vs temperature graph times the 25 °C value. | |
| Zero-gate-voltage drain current | I_DSS | A | max | Electrical Characteristics, row "Zero Gate Voltage Drain Current" (I_DSS), at V_DS = the rated voltage. | |
| Gate-body leakage current | I_GSS | A | max | Electrical Characteristics, row "Gate-Body Leakage Current" (I_GSS) at V_GS = ±the rated gate voltage. | |
| Gate resistance | R_G | Ohm | typ | Electrical Characteristics, row "Gate Resistance" (R_G) at f = 1 MHz. | |
| Gate-source charge | Q_gs | C | typ | Electrical Characteristics, row "Gate-Source Charge" (Q_gs). | |
| Gate-drain (Miller) charge | Q_gd | C | typ | Electrical Characteristics, row "Gate-Drain Charge" (Q_gd). | |
| Turn-on delay time | t_d(on) | s | typ | Switching Characteristics, row "Turn-On Delay Time". The test circuit and R_G are in the conditions. | |
| Rise time | t_r | s | typ | Switching Characteristics, row "Rise Time". | |
| Turn-off delay time | t_d(off) | s | typ | Switching Characteristics, row "Turn-Off Delay Time". | |
| Fall time | t_f | s | typ | Switching Characteristics, row "Fall Time". | |
| Body diode continuous current | I_S | A | max | Absolute Maximum Ratings or Source-Drain Diode Characteristics, row "Continuous Source Current (Body Diode)". | |
| Body diode reverse recovery charge | Q_rr | C | typ | Source-Drain Diode table, row "Reverse Recovery Charge" (Q_rr), with I_F and di/dt in the footnote. | |
| Single-pulse avalanche energy | E_AS | J | max | Absolute Maximum Ratings, row "Single Pulse Avalanche Energy" (E_AS). The starting T_J, L and I_AS are in the footnote. | |
| Thermal resistance, junction to ambient | θ_JA | C/W | typ, max | Thermal Characteristics / Thermal Information table, row "Junction-to-Ambient" (R_θJA). Note the PCB it is quoted on (JEDEC 1s or 2s2p). | |
| Thermal resistance, junction to case | θ_JC | C/W | typ, max | Thermal Characteristics table, row "Junction-to-Case" (R_θJC). For power packages use the tab / bottom value. | |
| Maximum junction temperature | T_J(max) | C | max | Absolute Maximum Ratings table, row "Junction Temperature" or "Operating Junction Temperature" (T_J). | |
| Power dissipation | P_D | W | max | Absolute Maximum Ratings, row "Power Dissipation" (P_D or P_tot) at T_A = 25 °C. If only a derating curve exists read its 25 °C value. | |
| Pin count | N_pins | typ | Package / Pin Configuration drawing on page 1 or 2. Count every terminal including the exposed pad. |
Transistor · PNP BJT (transistor.pnp → device pnp)
Simulation pins: c, b, e. Curves: DC current gain vs collector current, Base-emitter voltage vs collector current, Collector-emitter saturation vs current, Transition frequency vs collector current, Output capacitance vs collector-base voltage.
| Field | Symbol | Unit | Columns | Sets | Where to find it in the datasheet |
|---|---|---|---|---|---|
| DC current gain * | h_FE | min, typ, max | Electrical Characteristics, "ON Characteristics", row "DC Current Gain" (h_FE) at the I_C / V_CE closest to your circuit (for example I_C = −10 mA, V_CE = −1 V). | ||
| Collector-emitter voltage | V_CEO | V | max | Absolute Maximum Ratings, row "Collector-Emitter Voltage" (V_CEO, base open). Store as a positive number. | |
| Continuous collector current | I_C | A | max | Absolute Maximum Ratings, row "Collector Current - Continuous" (I_C). Store as a positive number. | |
| Collector-emitter saturation voltage | V_CE(sat) | V | typ, max | ON Characteristics, row "Collector-Emitter Saturation Voltage" at I_C / I_B = 10. Store as a positive number. | |
| Base-emitter voltage | V_BE(on) | V | min, typ, max | ON Characteristics, row "Base-Emitter On Voltage" V_BE(on) (or V_BE(sat)) at the stated I_C. Store as a positive number. | |
| Transition frequency | f_T | Hz | min, typ | Small-Signal Characteristics, row "Current-Gain-Bandwidth Product" (f_T). | |
| Output capacitance | C_obo | F | max | Small-Signal Characteristics, row "Output Capacitance" (C_obo, C_CB at V_CB = 5 V, 1 MHz). | |
| Input capacitance | C_ibo | F | max | Small-Signal Characteristics, row "Input Capacitance" (C_ibo, C_EB at V_EB = 0.5 V, 1 MHz). | |
| Early voltage (model) | V_AF | V | typ | Rarely listed: extrapolate the I_C vs V_CE output curves back to I_C = 0. Typical 50 to 150 V for small-signal parts. | |
| Turn-on time (delay + rise) | t_d + t_r | s | max | Switching Characteristics, rows "Delay Time" and "Rise Time". Add them. | |
| Turn-off time (storage + fall) | t_s + t_f | s | max | Switching Characteristics, rows "Storage Time" and "Fall Time". Add them. | |
| Collector-base voltage | V_CBO | V | max | Absolute Maximum Ratings, row "Collector-Base Voltage" (V_CBO). | |
| Emitter-base voltage | V_EBO | V | max | Absolute Maximum Ratings, row "Emitter-Base Voltage" (V_EBO). | |
| Peak collector current | I_CM | A | max | Absolute Maximum Ratings, row "Peak Collector Current" (I_CM), with the pulse width in the footnote. | |
| Collector cut-off current | I_CBO | A | max | Electrical Characteristics, row "Collector Cut-Off Current" (I_CBO). | |
| Emitter cut-off current | I_EBO | A | max | Electrical Characteristics, row "Emitter Cut-Off Current" (I_EBO). | |
| Base-emitter saturation voltage | V_BE(sat) | V | typ, max | Electrical Characteristics, row "Base-Emitter Saturation Voltage". I_C and I_B (usually a ratio of 10) in the conditions. | |
| Storage time | t_s | s | max | Switching Characteristics, row "Storage Time". | |
| Noise figure | NF | dB | typ | Electrical Characteristics, row "Noise Figure" with source resistance and f. | |
| Thermal resistance, junction to ambient | θ_JA | C/W | typ, max | Thermal Characteristics / Thermal Information table, row "Junction-to-Ambient" (R_θJA). Note the PCB it is quoted on (JEDEC 1s or 2s2p). | |
| Thermal resistance, junction to case | θ_JC | C/W | typ, max | Thermal Characteristics table, row "Junction-to-Case" (R_θJC). For power packages use the tab / bottom value. | |
| Maximum junction temperature | T_J(max) | C | max | Absolute Maximum Ratings table, row "Junction Temperature" or "Operating Junction Temperature" (T_J). | |
| Power dissipation | P_D | W | max | Absolute Maximum Ratings, row "Power Dissipation" (P_D or P_tot) at T_A = 25 °C. If only a derating curve exists read its 25 °C value. | |
| Pin count | N_pins | typ | Package / Pin Configuration drawing on page 1 or 2. Count every terminal including the exposed pad. |
Transistors · Darlington array (transistors.darr → device darr)
Simulation pins: in1, in2, in3, in4, in5, in6, in7, gnd, com, out7, out6, out5, out4, out3, out2, out1. Symbol variants: uln2003, uln2803.
| Field | Symbol | Unit | Columns | Sets | Where to find it in the datasheet |
|---|---|---|---|---|---|
| Collector-emitter saturation * | V_CE(sat) | V | max | vce_sat | Electrical characteristics, "V_CE(sat)" at I_C = 200 mA (or 350 mA). |
| Output current per channel | I_C | A | max | imax | Absolute maximum, "Output current". |
| Input resistance | R_IN | Ohm | typ | rin | Equivalent schematic: series input resistor (2.7 kΩ for ULN2003). |
| Output voltage | V_CE | V | max | Absolute maximum, "Output voltage" (informational). | |
| Operating temperature range | T_op | C | min, max | Features or Recommended Operating Conditions, row "Operating Temperature Range" (minimum and maximum). | |
| Pin count | N_pins | typ | Package / Pin Configuration drawing on page 1 or 2. Count every terminal including the exposed pad. | ||
| Thermal resistance, junction to ambient | θ_JA | C/W | typ, max | Thermal characteristics table, "Thermal resistance junction to ambient". |