Source code coming soon. The GitHub repository is private for now and opens to everyone very soon.
BetterSPICE Beta 0.8.0 Join the beta Download soon
Part VI  Parts and modelsReferenceContentsIndex
36

Devices: power ICs, drivers and protection

Regulator, converter, charger and driver ICs with their real pins, controller ICs, and protection parts. The parameter tables use the same columns as Devices: passives. Every part has labelled fields with units in the inspector and in All parameters, and the live stimulus of a sensor (light, temperature, field, strain, distance, load) is its main field, first in the list, with a slider range that fits it. A field that shows auto takes a value derived from other parameters until you type one (for example the must-operate voltage of a relay is 0.75 of its coil voltage). Clear it to go back. A variant placed from the library starts with its own typical values, such as 1 kΩ for a Pt1000 or 1.2 V dropout for an AMS1117. A part placed from the library can start with its own values, and a part made with the Part Wizard takes them from its datasheet fields (Part templates reference).

36.1Power ICs

These are regulators and drivers with their real pins: enable, feedback, switch node, power good. Unlike the power block (Power block) they are wired like the real chip, with the external divider, inductor and capacitors.

LDO regulator ICs

LDO regulator ICs
TypePinsVariantsClass
ldo (U)fixed3: IN, GND, OUT. adj3 (LM317): ADJ, OUT, IN. en5 (SOT-23-5): IN, GND, EN, NC, OUT. en_pg: IN, OUT, EN, PG, GND. neg3 (79xx): GND, IN, OUT. ams1117: GND, OUT, IN. adj5 (MIC29752): EN, IN, GND, OUT, ADJ.fixed3, adj3, en5, en_pg, neg3, ams1117, adj5approximate, LM317 verified ±0.76 %

A pass element that regulates the output to vset (or vref above ADJ for the adjustable types), limited by the dropout and the current limit, with a small sink, an overvoltage clamp and an internal 1 MΩ discharge. Enable pins turn it on above ven_on. The power-good output is open drain and releases above 92 % of the target.

LDO regulator ICs
ParameterKeyUnitDefaultRangeValue comes fromWhat it does
Output voltagevsetV3.3 (neg3 5)any (magnitude used)Default, inspector, part fileFixed types.
Reference / ADJ voltagevrefV1.25 (adj5 1.24)> 0Default, inspector, part fileAdjustable types: Vout = vref x (1 + R2/R1).
DropoutvdoV0.3 (ams1117 and adj3 1.2)≥ 0Default, inspector, part fileAt ilim.
Current limitilimA0.6 (ams1117 1.0)> 0Default, inspector, part file
Quiescent currentiqA50 µA≥ 0Default, inspector, part file
ADJ pin currentiadjA50 µA≥ 0File or All parametersadj3.
Enable thresholdven_onV1.0≥ 0Default, inspector, part file
Output resistanceroutΩ0.02> 0File or All parameters
ADJ transconductancegmA/V104> 0File or All parametersadj5.

Key: the name in the circuit file, in a parameter step (R1.r) and for AI agents. Range: a value outside it is refused with E_PARAM. Value comes from: where you can set it. The All parameters tab and agents can set every parameter.

Try it
An LM317 at 5 V
  1. Place an LDO IC, variant adj3. Wire IN to 9 V, a 240 Ω resistor from OUT to ADJ and 720 Ω from ADJ to ground, and a 100 mA load.
  2. Probe OUT.

You should seeOUT settles at 1.25 x (1 + 720/240) = 5.0 V. Lower the input with its slider and the output follows the input 1.2 V below once it is in dropout.

Buck converter ICs

Buck converter ICs
TypePinsVariantsClass
buckic (U)async, module: VIN, SW, GND, FB, EN, BST. sync: plus PG.async (external diode), sync, moduleapproximate

Regulates V(FB) to vref, so the external divider sets the output, and sources the inductor current from SW. By default it’s an averaged model, fast and smooth. Set ripple above 0.5 for the switching peak-current-mode form, which shows the real switch node and ripple in a transient. EN has a pull-up to VIN, so an open EN enables. The reference soft-starts over ss_time.

Buck converter ICs
ParameterKeyUnitDefaultRangeValue comes fromWhat it does
Feedback voltagevrefV0.8> 0Default, inspector, part file
Switching frequencyfswHz500 kHz> 0Default, inspector, part fileSwitching form.
Switch current limitilimA3> 0Default, inspector, part file
High-side / low-side Rds(on)ron_hs, ron_lsΩ0.1, 0.08> 0Default, inspector, part file
Soft-start timess_times1 ms≥ 0Default, inspector, part file
Maximum dutydmax0.950.05 to 1File or All parameters
Enable thresholdven_onV1.2≥ 0File or All parameters
Quiescent currentiqA0.5 mA≥ 0Default, inspector, part file
Switching formripple00 to 1File or All parametersAbove 0.5: switching.
Error-amp gainkpA/V2> 0File or All parameters
Dead timedeadtimes20 ns≥ 0File or All parameterssync.
Reverse current limitilim_negA0 (diode emulation)≥ 0File or All parameters

Key: the name in the circuit file, in a parameter step (R1.r) and for AI agents. Range: a value outside it is refused with E_PARAM. Value comes from: where you can set it. The All parameters tab and agents can set every parameter.

Boost converter ICs

Boost converter ICs
TypePinsVariantsClass
boostic (U)async: SW, GND, FB, EN, VIN. sync: plus VOUT.async (MT3608), syncapproximate

Peak-current-mode boost: a low-side switch from SW to ground, a PI loop on FB, slope compensation. The async type needs an external diode. EN has a pull-down, so an open EN disables it. It runs above 2 V input.

Boost converter ICs
ParameterKeyUnitDefaultRangeValue comes fromWhat it does
Feedback voltagevrefV0.6> 0Default, inspector, part file
Switching frequencyfswHz1.2 MHz> 0Default, inspector, part file
Switch current limitilimA4> 0Default, inspector, part file
Switch on resistanceronΩ0.08> 0Default, inspector, part file
Maximum dutydmax0.90.05 to 0.98Default, inspector, part file
Soft-start timess_times1 ms≥ 0File or All parameters
Slope compensationslopeA/s0.3 x ilim x fsw≥ 0File or All parameters

Key: the name in the circuit file, in a parameter step (R1.r) and for AI agents. Range: a value outside it is refused with E_PARAM. Value comes from: where you can set it. The All parameters tab and agents can set every parameter.

Load switches, eFuses and ideal diodes

Load switches, eFuses and ideal diodes
TypePinsVariantsClass
loadsw (U)loadsw: VIN, VOUT, ON, GND. efuse: VIN, VOUT, EN, ILIM, GND. ideal_diode: IN, OUT, CE, GND. hiside: IN, OUT, ON, GND.loadsw, efuse, ideal_diode, hisideapproximate

A switch with a controlled output rise and no reverse current. The eFuse limits current to k_ilim / R_ILIM and shuts off after t_flt in limit, until its enable is toggled. The ideal diode conducts only forward, with about 20 mV drop.

Load switches, eFuses and ideal diodes
ParameterKeyUnitDefaultRangeValue comes fromWhat it does
On resistanceronΩ0.03> 0Default, inspector, part file
Output rise timet_rises1 ms> 0Default, inspector, part file
ILIM constantk_ilimA·Ω105> 0File or All parameterseFuse limit = k_ilim / R_ILIM.
ON thresholdvonV1.0≥ 0Default, inspector, part file
Quick output dischargeqod0 / 11File or All parameters100 Ω on VOUT while off.
Fault timet_flts1 ms> 0File or All parameterseFuse.

Key: the name in the circuit file, in a parameter step (R1.r) and for AI agents. Range: a value outside it is refused with E_PARAM. Value comes from: where you can set it. The All parameters tab and agents can set every parameter.

Li-ion chargers and battery protection

Li-ion chargers and battery protection
TypePinsVariantsClass
charger (U)tp4056: TEMP, PROG, GND, VCC, BAT, STDBY, CHRG, CE. mcp73831: STAT, VSS, VBAT, VDD, PROG.tp4056, mcp73831approximate, TP4056 verified ±0.08 %

Constant current set by the resistor on PROG (I = k_prog / R_PROG), a trickle below v_trickle, constant voltage at vfloat, termination below i_term. The status outputs are open drain: CHRG low while charging, STDBY low when done.

Li-ion chargers and battery protection
ParameterKeyUnitDefaultRangeValue comes fromWhat it does
Regulation voltagevfloatV4.2> 0Default, inspector, part file
PROG constantk_progV1200 (mcp73831 1000)> 0Default, inspector, part file
Termination ratioi_termx I_chg0.10 to 1Default, inspector, part file
Trickle thresholdv_trickleV2.9> 0Default, inspector, part file
Minimum inputvin_minV4.0> 0File or All parameters

Key: the name in the circuit file, in a parameter step (R1.r) and for AI agents. Range: a value outside it is refused with E_PARAM. Value comes from: where you can set it. The All parameters tab and agents can set every parameter.

Li-ion chargers and battery protection
TypePinsVariantsClass
batprot (U)OD, CS, OC, TD, VCC, GNDnone (DW01A class)approximate

Drives the discharge-FET gate OD low on overdischarge or overcurrent and the charge-FET gate OC low on overcharge, each after its delay.

Li-ion chargers and battery protection
ParameterKeyUnitDefaultRangeValue comes fromWhat it does
Overcharge detectionv_ocV4.25> 0Default, inspector, part file
Overdischarge detectionv_odV2.4> 0Default, inspector, part file
Overcurrent detectionv_ocpV0.15> 0Default, inspector, part fileOn CS.
Delayst_oc, t_od, t_ocps80 ms, 40 ms, 10 ms≥ 0Default, inspector, part file
Short-circuit thresholdv_scV1.35> 0File or All parametersTrips with no delay.

Key: the name in the circuit file, in a parameter step (R1.r) and for AI agents. Range: a value outside it is refused with E_PARAM. Value comes from: where you can set it. The All parameters tab and agents can set every parameter.

Power modules and off-line switchers

Power modules and off-line switchers
TypePinsVariantsClass
psu_module (PS)dcdc: VIN, GND, VOUT, EN. dcdc_iso: VIN+, VIN-, VOUT+, VOUT-. acdc: L, N, V+, V-.dcdc, dcdc_iso, acdcapproximate

A finished module: a Thevenin output of vout behind rout, input power = output power / eff, on above vin_min. The isolated and AC types keep input and output separate. The output isn’t current limited. It warns above 110 % of pout.

Power modules and off-line switchers
ParameterKeyUnitDefaultRangeValue comes fromWhat it does
Output voltagevoutV5anyDefault, inspector, part file
Output powerpoutW3> 0Default, inspector, part file
Efficiencyeff0.750.05 to 1Default, inspector, part file
Input rangevin_min, vin_maxV4.5, 5.5 (acdc 85, 265 V RMS)Default, inspector, part file
Output resistanceroutΩ0.05> 0File or All parameters
Rippleripple, fswV p-p, Hz0.05, 65 kHzDefault, inspector, part file

Key: the name in the circuit file, in a parameter step (R1.r) and for AI agents. Range: a value outside it is refused with E_PARAM. Value comes from: where you can set it. The All parameters tab and agents can set every parameter.

Power modules and off-line switchers
TypePinsVariantsClass
offline (U)buck: D, S, FB, BP. flyback: D, S, FB, VDD.buck, flybackapproximate

An averaged on/off off-line switcher (LNK, TNY class): the switch current from D to S rises while FB is below vfb, limited to half of ilim and by Rds(on). The supply pin is regulated from the drain.

Power modules and off-line switchers
ParameterKeyUnitDefaultRangeValue comes fromWhat it does
Current limitilimA0.25> 0Default, inspector, part file
Feedback thresholdvfbV1.65> 0Default, inspector, part file
MOSFET on resistancerds_onΩ24> 0Default, inspector, part file

Key: the name in the circuit file, in a parameter step (R1.r) and for AI agents. Range: a value outside it is refused with E_PARAM. Value comes from: where you can set it. The All parameters tab and agents can set every parameter.

Motor drivers

Motor drivers
TypePinsVariantsClass
hbridge2 (U)in_in: AIN1, AIN2, BIN1, BIN2, AOUT1, AOUT2, BOUT1, BOUT2, VM, GND, nSLEEP. pwm_dir: AIN1, AIN2, PWMA, BIN1, BIN2, PWMB, STBY, AO1, AO2, BO1, BO2, VM, VCC, GND.in_in (DRV8833, L298), pwm_dir (TB6612)approximate

Four half bridges with body diodes and dead time. in_in truth table per channel: 00 coast, 10 forward, 01 reverse, 11 brake. pwm_dir: IN1 and PWM forward, IN2 and PWM reverse, PWM low brakes, STBY low turns everything off. Overcurrent protection: a switch current above ilim turns that bridge off (a W_RATING warning) and it retries after 1.6 ms, as the DRV8833 does.

Motor drivers
ParameterKeyUnitDefaultRangeValue comes fromWhat it does
Output on resistanceronΩ0.36> 0Default, inspector, part fileHigh plus low side.
Overcurrent tripilimA2> 0File or All parametersPer switch; the bridge retries after 1.6 ms.
Dead timedeadtimes200 ns≥ 0File or All parameters

Key: the name in the circuit file, in a parameter step (R1.r) and for AI agents. Range: a value outside it is refused with E_PARAM. Value comes from: where you can set it. The All parameters tab and agents can set every parameter.

Motor drivers
TypePinsVariantsClass
stepdrv (U)EN, MS1, MS2, MS3, RST, SLP, STEP, DIR, VMOT, GND, 1A, 1B, 2A, 2B, VDD, VREFa4988, drv8825approximate

Each rising STEP edge moves one microstep in the direction of DIR. MS1 to MS3 set full to 1/16 (A4988) or 1/32 (DRV8825) stepping. The winding currents follow sine and cosine of the step angle, limited by VREF / (8 rsense) for the A4988 or VREF / (5 rsense) for the DRV8825. Set ripple above 0.5 for the chopper form.

Motor drivers
ParameterKeyUnitDefaultRangeValue comes fromWhat it does
Sense resistorrsenseΩ0.1> 0Default, inspector, part file
Current limitilimA1> 0Default, inspector, part fileUsed when VREF is not wired.
Output on resistanceronΩ0.32> 0Default, inspector, part fileChopper form.
Off timetoffs20 µs> 0Default, inspector, part file
Chopper formripple00 to 1File or All parameters

Key: the name in the circuit file, in a parameter step (R1.r) and for AI agents. Range: a value outside it is refused with E_PARAM. Value comes from: where you can set it. The All parameters tab and agents can set every parameter.

36.2Controller and driver ICs

These switch for real, edge by edge. Logic inputs and comparators are found to the exact instant. Outputs move with short edges behind their source and sink resistance. Output current comes from the part's own supply pins, so bootstrap capacitors discharge into the gate as on a board.

Controller and driver ICs
TypePinsVariantsClass
gatedrv (U)low: IN, VDD, GND, OUT. high_boot: IN, VDD, GND, HO, HS, VB. half_bridge: HIN, LIN, VDD, GND, HO, HS, LO, VB. isolated: IN, VDD1, GND1, OUT, GND2, VDD2, the two sides joined only by r_iso and c_iso (an old 4-pin isolated driver keeps one ground).low, high_boot, half_bridge, isolatedapproximate, verified ±6.3 %
Controller and driver ICs
ParameterKeyUnitDefaultRangeValue comes fromWhat it does
VDD UVLOvdd_uvlo, vdd_hysV4.5, 0.3Default, inspector, part fileOutputs held low below.
VB-HS UVLOvb_uvloV4.2> 0Default, inspector, part file
Peak source / sink currentsrc_a, snk_aA2, 3> 0Default, inspector, part fileOutput resistance = 10 V / current.
Propagation delaytpds20 ns (placed 50 ns)≥ 0Default, inspector, part file
Dead timedeadtimes0≥ 0Default, inspector, part fileHalf bridge.
Input threshold, hysteresisvth, vhysV1.65, 0.8Default, inspector, part file
Interlockinterlock0 / 10Default, inspector, part fileBoth outputs low if both inputs are high.
Bootstrap diodeboot_diode0 / 11Default, inspector, part file

Key: the name in the circuit file, in a parameter step (R1.r) and for AI agents. Range: a value outside it is refused with E_PARAM. Value comes from: where you can set it. The All parameters tab and agents can set every parameter.

Controller and driver ICs
TypePinsVariantsClass
hbridge (U)VM, GND, IN1, IN2, OUT1, OUT2in1_in2 (DRV8871), pwm_dirapproximate

Four switches with body diodes. in1_in2: 00 coast, 10 forward, 01 reverse, 11 brake. A high-side current above ilim recirculates for 25 µs.

Controller and driver ICs
ParameterKeyUnitDefaultRangeValue comes fromWhat it does
Switch on resistancerds_onΩ0.5 (placed 0.1)> 0Default, inspector, part file
Dead timedeadtimes200 ns≥ 0Default, inspector, part file
Current limitilimA3.6> 0Default, inspector, part file
Input thresholdvthV1.5> 0Default, inspector, part file
VM UVLOvm_uvloV4.0> 0Default, inspector, part file

Key: the name in the circuit file, in a parameter step (R1.r) and for AI agents. Range: a value outside it is refused with E_PARAM. Value comes from: where you can set it. The All parameters tab and agents can set every parameter.

Controller and driver ICs
TypePinsVariantsClass
supervisor (U)VIN, GND, OUTreset, uvlo, windowapproximate
Controller and driver ICs
ParameterKeyUnitDefaultRangeValue comes fromWhat it does
ThresholdvthV2.93> 0Default, inspector, part fileFalling.
HysteresishysV1 % of vth≥ 0Default, inspector, part file
Reset delaydelays200 µs (reset)≥ 0Default, inspector, part file
Window upper limitvth_hiV1.1 x vth> 0Default, inspector, part file
Outputrout, open_drain, active_high100 Ω, 0, 0Default, inspector, part file

Key: the name in the circuit file, in a parameter step (R1.r) and for AI agents. Range: a value outside it is refused with E_PARAM. Value comes from: where you can set it. The All parameters tab and agents can set every parameter.

Controller and driver ICs
TypePinsVariantsClass
pwmctl (U)VIN, GND, FB, COMP, CS, GATE, SS, EN, RT, and for the synchronous form SW, BOOT, HO, LOvmode, cmode (UC3843), hyst, cot, pfc_tm (L6562), llc, qrapproximate, verified ±0.04 to ±7.9 %

A switching controller. An error amplifier on FB drives COMP, and the reference starts softly. UVLO and an enable are built in. vmode compares COMP with a ramp. cmode turns off when CS reaches the COMP level (with slope compensation and leading-edge blanking). hyst and cot are hysteretic and constant on-time. pfc_tm is transition-mode PFC and qr is quasi-resonant valley switching. llc is a 50 % half bridge whose frequency falls as COMP rises.

Controller and driver ICs
ParameterKeyUnitDefaultRangeValue comes fromWhat it does
ReferencevrefV0.8 (pfc_tm 2.5)> 0Default, inspector, part file
Switching frequencyfswHz200 kHz> 0Default, inspector, part file
Error amplifierea_gm, ea_gainS, -1 mS, 104> 0Default, inspector, part file
Duty limitsdmin, dmax0, 0.90 to 1, dmin < dmaxDefault, inspector, part file
Slope compensationslopeV/s0≥ 0Default, inspector, part filecmode.
CS gain, limitcs_gain, cs_limit-, V3, 1.0> 0Default, inspector, part file
Soft startss_times1 ms≥ 0Default, inspector, part file
UVLOuvlo_on, uvlo_offV4.5, uvlo_on - 0.5uvlo_off < uvlo_onDefault, inspector, part fileSet both when lowering uvlo_on below 4 V.
Dead timedeadtimes50 ns≥ 0Default, inspector, part file
Gate drivegate_driveA1.0> 0Default, inspector, part file
On-timetons1 µs (pfc_tm 10 µs)> 0Default, inspector, part file
Blankingblankings100 ns≥ 0Default, inspector, part file
Ramp amplitudevrampV2.0> 0Default, inspector, part filevmode.
Hysteresis windowvhysV10 mV≥ 0Default, inspector, part filehyst.
Frequency rangefmin, fmaxHz0.5 x fsw, 2 x fswfmin < fmaxDefault, inspector, part filellc, qr, pfc.
ZCD thresholdzcd_thV50 mV> 0Default, inspector, part file
Gate clampvclampV15> 0Default, inspector, part file
Minimum off timetoff_mins200 ns≥ 0Default, inspector, part file
Restartt_restarts50 µs> 0Default, inspector, part file

Key: the name in the circuit file, in a parameter step (R1.r) and for AI agents. Range: a value outside it is refused with E_PARAM. Value comes from: where you can set it. The All parameters tab and agents can set every parameter.

Controller and driver ICs
TypePinsVariantsClass
ledctl (U)VIN, GND, CS, GATE, DIMbuck_cc, boost_ccapproximate

Fixed-frequency peak-current LED driver: GATE on each cycle, off when CS reaches vcs. DIM enables it.

Controller and driver ICs
ParameterKeyUnitDefaultRangeValue comes fromWhat it does
CS thresholdvcsV0.2> 0Default, inspector, part file
Switching frequencyfswHz100 kHz (placed 200 kHz)> 0Default, inspector, part file
Blanking, gate drive, clamp, dmax, UVLOblanking, gate_drive, vclamp, dmax, uvlo_on100 ns, 1 A, 15 V, 0.95, 4.5 VDefault, inspector, part file

Key: the name in the circuit file, in a parameter step (R1.r) and for AI agents. Range: a value outside it is refused with E_PARAM. Value comes from: where you can set it. The All parameters tab and agents can set every parameter.

Controller and driver ICs
TypePinsVariantsClass
uc384x (U)COMP, FB, CS, RTCT, GND, OUT, VCC, VREF (the UC3842 / UC3843 DIP order)noneapproximate, checked against the vendor models in Simulate

The live view's stand-in for a vendor UC384x current-mode controller (new in 0.8.0). It is not placed from the library: a vendor UC3843 part carries it as its live equivalent, and Simulate keeps running the vendor model. UVLO on VCC with a clamp, VREF behind its output resistance with a current limit and line regulation, a transconductance error amplifier into COMP, the RT/CT oscillator, the current comparator and the latch set by the oscillator pulse once the comparator releases it (reset wins). With COMP pulled below two diode drops the output stays low, the datasheet's shutdown. The four UC3843 examples set its numbers to the vendor model's.

Controller and driver ICs
ParameterKeyUnitDefaultRangeValue comes fromWhat it does
UVLOuvlo_on, uvlo_offV8.4, 7.6uvlo_off < uvlo_onDefault, inspector, part file
Supply currentiq_off, iq_onA0.5 mA, 11 mA≥ 0Default, inspector, part fileThe start-up and operating currents of the TI datasheet.
ReferencevrefV5> 0Default, inspector, part fileBehind ref_rout, limited by ref_ilim. ref_lnr gives the line regulation around ref_vnom (12 V), 0 by default.
Oscillator thresholdsosc_hi, osc_loV2.8, 1.1osc_lo < osc_hiDefault, inspector, part fileRT/CT, discharged by idis (8.3 mA).
Current sensecs_off, cs_gain, cs_maxV, -, V1.4, 3, 1> 0Default, inspector, part fileThe trip level is min(max((V(COMP) - cs_off) / cs_gain, 0), cs_max).

Key: the name in the circuit file, in a parameter step (R1.r) and for AI agents. Range: a value outside it is refused with E_PARAM. Value comes from: where you can set it. The All parameters tab and agents can set every parameter.

Controller and driver ICs
TypePinsVariantsClass
chgctl (U)VIN, BAT, GND, CS, GATEcccv (Li-ion), float (lead-acid)approximate

A linear charger that drives an external PMOS or PNP: precharge, constant current set by the sense resistor between CS and BAT, constant voltage, termination.

Controller and driver ICs
ParameterKeyUnitDefaultRangeValue comes fromWhat it does
Charge currentichgA1> 0Default, inspector, part file
Float voltagevfloatV4.2 (float 13.6)> 0Default, inspector, part file
Termination currentitermA0.1 x ichg≥ 0Default, inspector, part file
Precharge current, thresholdprecharge, vpreA, V0.1 x ichg, 3.0Default, inspector, part file
Sense resistorrsenseΩ0.1> 0Default, inspector, part file

Key: the name in the circuit file, in a parameter step (R1.r) and for AI agents. Range: a value outside it is refused with E_PARAM. Value comes from: where you can set it. The All parameters tab and agents can set every parameter.

36.3Diodes, thyristors and protection

Diodes are fitted to their forward voltage at a test current, and breakdown is a smooth clamp with a dynamic resistance. Thyristors latch on a trigger and hold until their current falls below the holding current.

Diodes, thyristors and protection
PartTypePinsWhat it doesParameters (default)
Bidirectional TVSdiode, variant tvs_bianode, cathodeClamps at ± bv in both directions.bv (6.8 V), rdyn (0.5 Ω), cj0 (100 pF)
Bridge rectifierbridge (D)ac1, ac2, +, -Four diodes with reverse breakdown.vf (1 V) at if_test (1 A), bv (1000 V), cj0 (20 pF)
Dual diodediode2 (D)cc: a1, a2, k. ca: k1, k2, a. series: a, mid, k. dual: a1, k1, a2, k2Two diodes in one package.kind (signal: 0.75 V at 10 mA, bv 75 V, or schottky: 0.4 V, bv 30 V), is, n, bv, cj0 (2 pF)
ESD protection arrayesd (D)1ch: io, gnd. 2ch: io1, io2, gnd. 4ch, 2ch_vbus, 4ch_vbus, usblc6 (6 pins)Steering diodes to gnd and VBUS and a TVS clamp.vbr (6.5 V), vc (12 V) at ipp (5 A), cj (1 pF) per line
Current-regulating diodecrd (D)anode, cathodeHolds a constant current above the knee voltage.ip (10 mA), vk (2.5 V)
SCRscr (Q)anode, cathode, gateFires on gate current above igt, on breakover above vdrm or on dV/dt above dvdt_crit. Holds above ih.igt (200 µA), ih (5 mA), vtm (1.4 V) at itm (5 A), vgt (0.8 V), vdrm (600 V), dvdt_crit (50 V/µs)
TRIACtriac (Q)mt1, mt2, gateFires on gate current of either sign above igt (quadrant 4 only if allowed) or above vdrm.igt (10 mA), ih (15 mA), vtm (1.5 V) at itm (10 A), vgt (1 V), vdrm (600 V), quadrants (123)
DIAC, SIDAC, surge suppressordiac (D)a, bBreaks over at vbo in either direction.vbo (32 V, sidac 120, tss 58), dv fold-back (6 V), ih, ron
Varistor (MOV)mov (RV)a, bI = 1 mA x (V / v1ma)alpha. Warns when the absorbed energy exceeds e_max.v1ma (470 V), alpha (30), c (100 pF), r_bulk (1 Ω), e_max (10 J)
Gas discharge tubegdt (GDT)2pin: a, b. 3pin: a, b, gndSparks over at v_spark (higher for fast edges), glows, then arcs above i_glow, extinguishes below i_hold.v_spark (90 V), v_arc (15 V), v_glow (0.7 x v_spark), i_glow (0.5 A), i_hold (0.1 A), k_imp (0.1)
Try it
A crowbar with an SCR
  1. Place a 12 V source with 1 Ω in series, an SCR across the output, a 9.1 V Zener from the output to the gate through 100 Ω, and 1 kΩ from gate to cathode.
  2. Raise the source slowly with its slider.

You should seeAbove about 9.8 V the Zener drives the gate, the SCR fires and shorts the output, and it stays on until the source drops below the point where the current falls under ih.