09
Task index
Find your goal, in your own words. The grey words are what other people call the same thing, so a search for "Bode" or "bias point" lands here too.
| I want to … | Section |
|---|---|
| Add a datasheet graph to a part (curve, digitize, paste a table, datasheet graph, R_DS(on) vs temperature, fit the model) | 12.5 |
| Build the inside of a subcircuit myself (edit subcircuit, blank IC, make a block, sub-sheet tab, X1, subckt) | 10.9 |
| Change the colours or the theme | 19.7 |
| Check a circuit across component tolerances (tolerance, worst case, min typ max, corner, Monte Carlo, yield, spread, histogram) | 11.12 |
| Check a power supply: start-up, load step and ripple (ripple, load transient, soft start, overshoot, settling time, regulator, buck converter, LDO) | 11.11 |
| Choose the model a part uses (assign model, vendor model, SPICE model, change model, model card) | 12.1 |
| Compare a run with an earlier one (reference, before and after, compare runs, keep a trace, difference) | 11.14 |
| Draw or edit a symbol (symbol editor, custom symbol, pinout, IC box, bssym) | 12.6 |
| Export a netlist for another simulator (netlist, ngspice, cir, LTspice, SPICE export) | 13.5 |
| Find a part or a vendor model in the library (search parts, find a model, part number, MPN, component library) | 10.6 |
| Find out why every voltage is 0 V | 14.1 |
| Find the DC operating point of every net (bias point, quiescent point, DC voltages, node voltages, OP) | 11.9 |
| Find the frequency response and the phase margin (Bode plot, AC analysis, gain margin, stability, -3 dB, bandwidth, cutoff frequency, loop gain) | 11.6 |
| Fix a run that will not converge (did not converge, E_NEWTON, E_SINGULAR, E_TIMESTEP, halted, convergence, Gear) | 11.16 |
| Get a model from datasheet numbers (Quick model, fit a model, datasheet values, no model available) | 12.2 |
| Go back in time in a paused run (scrub, playhead, replay, history, go to a time) | 11.20 |
| Hand a task to an AI agent and check what it did (Claude, AI, MCP, agent, automate design) | 13.7 |
| Import a KiCad or EasyEDA Pro design (KiCad, EasyEDA, import schematic, kicad_sch, epro) | 13.1 |
| Keep sides isolated with their own grounds (isolated ground, floating ground, galvanic isolation, optocoupler, transformer, ISO1, secondary side, second ground, ground domain) | 10.3 |
| Know which result to trust | 06.7 |
| Learn every key | 17 |
| Look at digital signals on the logic analyzer (logic analyzer, digital waveform, bus value, trigger on edge, counter) | 11.19 |
| Make a part from a datasheet (Part Wizard, new part, custom part, bspart, create component) | 12.4 |
| Measure time, amplitude and frequency with cursors and stats (delay, rise time, peak to peak, RMS, frequency, duty cycle, measure) | 11.4 |
| Measure voltage and current at one point (probe, voltage and current, power at a point, both, current probe) | 11.17 |
| Name nets and use ground and power flags (net label, node name, supply rail, VCC, GND, global label, 0 V reference) | 10.2 |
| Open an example circuit | 54 |
| Organise a big circuit with sheets and buses (hierarchy, subcircuit, block, sub-sheet, bus) | 10.8 |
| Place, rotate and wire parts (add a component, draw a schematic, connect parts, rotate, mirror) | 10.1 |
| Plot a transfer curve with a DC sweep (DC analysis, transfer characteristic, IV curve, diode curve, sweep a source) | 11.8 |
| Pop a scope out onto a second monitor | 19.10 |
| Probe a signal and read it on the scope (scope, oscilloscope, measure voltage, measure current, trace, waveform) | 11.3 |
| Read a circuit file by hand | 48.2 |
| Recover unsaved work after a crash | 19.12 |
| Replace a model that does not run (broken model, retired model, model fails, stand-in, replacement) | 12.8 |
| Run a model that is encrypted (PSpice, Cadence encrypted, TI model, encrypted model) | 12.7 |
| Run a program on a microcontroller (MCU, Arduino, firmware, GPIO, blink an LED, code, UART, I2C, SPI, CAN, PWM, ADC) | 12.3 |
| Run a transient with Simulate (exact transient, time domain, F5, accurate run, tran) | 11.5 |
| Run simulations from a script (command line, bspice, batch, CI, automation, headless) | 13.6 |
| Save a picture, a plot or the data (export image, PNG, SVG, CSV, screenshot, copy plot) | 13.2 |
| Script a control block (PWM, state machine) | 40 |
| See the spectrum and distortion of a signal (FFT, harmonics, THD, spectrum analyser, noise floor) | 11.10 |
| See where the power goes in a circuit (energy, power flow, losses, efficiency, heat, where does the power go) | 11.15 |
| Select, move, copy and undo (duplicate, copy paste, box select, nudge, undo, redo) | 10.5 |
| Send a circuit to someone who has no BetterSPICE (share, link, viewer, interactive HTML, email a circuit, forum) | 13.4 |
| Set a pass or fail limit on a result (measurement, pass fail, limit, specification, rise time, overshoot, settling time, efficiency) | 11.13 |
| Set up ngspice or PSpice | 57.2 |
| Simulate a transmission line or PCB trace | 42 |
| Start a circuit from rest or from the operating point (power-on, initial conditions, capacitor starts empty, startup transient, ic, initial voltage, settled state) | 11.2 |
| Start a new ground domain (new ground, ISO2, another isolated side, rename ground domain, make main ground, ground name) | 10.4 |
| Stop it halting (didn't converge, E_NEWTON) | 14.2 |
| Sweep a part value and compare the curves (parameter step, .step, sweep resistor, what if, compare values) | 11.7 |
| Type exact values and tune them with sliders (change a value, SI prefix, potentiometer, slider range, set resistance) | 10.7 |
| Understand an E_ or W_ code | 15 |
| Watch a circuit run, slow it down or pause it (run, pause, timebase, speed, real time, reset) | 11.1 |
| Write a report (report, documentation, HTML report, print to PDF, in-depth report, datasheet for my design) | 13.3 |
| Zoom a paused trace to fit the screen (Fit Y, vertical zoom, autoscale, paused scope) | 11.18 |