18
Glossary
The words this manual uses with a set meaning. Each entry ends with where it’s explained.
- AC sweep
- A small-signal analysis that plots gain and phase against frequency around the DC operating point. Key F7. 28.3
- Activity
- The dock tab that logs every edit and run, by you or an AI agent. Alt+7. 26.16
- AI agent
- A program such as Claude Code that edits and simulates the open circuit through the bspice MCP server. 52
- Analysis view
- The area that shows the result of the analysis tab you have open (each tab keeps its own last result): plots, cursors, the operating point table. Ctrl+2. 29
- Approximate
- The class of behavioural device models, measured against a vendor model or a reference circuit. 06.6
- Badge
- A small count on the status bar's Diagnostics item: red for errors, amber when there are only warnings. 07.1
- BetterSPICE engine
- The built-in solver that Simulate uses for circuits without vendor model files. In the browser it runs as WebAssembly. 27.2
- Bode plot
- Gain in dB and phase in degrees against frequency on a log axis: the result of an AC sweep. 28.3
- Bus
- A thick line that stands for a group of signals. The member wires carry the connections. 22.11
- Calculator
- One of 17 design calculators (filter, LED resistor, via, trace impedance, dB and more) that can place a checked circuit. Ctrl+Shift+C. 47
- Catalogue
- The searchable set of vendor models inside the library, each run in a test circuit before it was listed. 43
- Class
- Exact or approximate: how closely a device type matches ngspice, shown in every device table. 06.6
- Command palette
- A search box over every command, part and model. Ctrl+K. 20.11
- Complementary PWM
- Two PWM outputs that are never high together, with a dead time between them:
pin LO complement HI dead 200nsin the MCU language. 41.10 - Console
- The dock tab that shows what programs print and what a USB-UART bridge receives, with an input bar to send text through the bridge. Alt+5. 26.15
- Convergence
- The solver finding a consistent set of voltages at an instant. When it cannot, you get E_NEWTON or E_TIMESTEP. 14.2
- CCVS, CCCS
- Current-controlled voltage source (H) and current source (F). The current they sense goes through their own s+ / s- port, wired in series with the branch. 31.13
- Convergence doctor
- The retry the engine makes by itself when a run does not converge. It keeps the first setting that works and reports it as W_CONVERGENCE_AIDS. 27.9
- Current dots
- Moving dots on wires whose speed shows the current. Display only. 25.7
- Cursor
- One of two vertical lines, A and B, that read values and the time between them on a plot. 26.10
- Decoder
- A lane of the Logic tab that reads a channel as UART, I2C, SPI, CAN, 1-Wire, PWM or Manchester and lists the frames. Saved in the circuit. 26.14
- DC operating point
- The steady DC state of the circuit: every net voltage and part current. Key F9. 28.5
- DC sweep
- An analysis that steps one source slowly and plots the steady result. Key F8. 28.4
- Diagnostic
- A coded report of a problem: severity, code, a message naming the part and net, and the fix. 15
- Digitizer
- The Part Wizard tool that reads points off an image of a datasheet graph from two clicked ticks on each axis. 45.6
- Document tab
- The tab above the canvas for each open circuit. Untitled circuits are numbered, examples say example, and the list at the right end of the strip shows them all. 19.4
- Dead time
- The gap between one PWM output turning off and its complement turning on, so a half bridge never shorts.
dead 200ns. 41.10 - Dock
- The tabbed area under the canvas: Scope, Bode, FFT, Logic, Console, Diagnostics, Activity. 7
- Energy view
- The canvas mode that draws bands of power on the wires and a ledger of input, output and losses. Alt+E. 25.8
- Fit Y
- The scope button that fits the vertical axis to the traces in view when a run is paused and zoomed. 26.5
- Generic (no vendor model)
- What the inspector shows for a part with no model: it simulates with built-in typical values. 06.5
- E_ code
- An error diagnostic. The run stops until you fix it. 15
- Encrypted model
- A vendor model that Cadence encrypted, so only PSpice can read it. Mostly Texas Instruments parts. 27.13
- Exact
- The class of devices that use the same equations as ngspice and are compared with it signal by signal. 06.6
- FFT
- A spectrum computed from a waveform. The FFT analysis uses a transient. The FFT tab shows a live trace. 28.8
- Fitted model
- A behavioural model whose parameters were measured by running a vendor model. The live simulation uses it for vendor chips. 44.9
- Floating net
- A net with no DC path to ground, for example between two capacitors. E_FLOATING_NET. 14.2
- Follow AI
- The switch that makes your view follow what an AI agent touches. Ctrl+Shift+F. 52.2
- Gear
- Gear-2, a second order integration method that damps ringing in stiff circuits. Chosen on the Transient tab. 28.2
- Global label
- A net name that joins nets on every sheet. Shift+N. 21.3
- gmin
- A tiny conductance to ground the solver adds when a DC point is hard to find. 28.5
- Ground
- Net 0, the 0 V reference every voltage is measured from. Every circuit needs one. G. 06.4
- Halted
- The state of the live simulation after an error it cannot get past. Click the red Halted button. 25.17
- Hierarchical sheet
- A block of the circuit inside a box with ports, opened by double-click. 22
- ic
- A part parameter that sets the initial voltage of a capacitor or current of an inductor at t = 0. The inspector calls it Initial voltage or Initial current. 30
- Inspector
- The pane on the right that shows and edits the selected part. 24
- Ground domain
- All grounds with the same name, such as ISO1: one net with its own isolation values. The main ground is the domain with no name. 10.4
- Isolated ground
- A ground with its own name (ISO1): a separate 0 V for a transformer secondary or an optocoupler output, tied to the main ground only through 1 GΩ and 10 pF, which belong to its domain. 06.4
- Key figures
- The numbers that matter for a vendor model (gain-bandwidth, slew rate, dropout and so on), each marked bench, measured, fit, card or sheet. 44.3
- Library
- The left pane: every placeable part type and every model, in families. 23
- Live engine
- The solver behind the live simulation: Live MNA · WASM, or · JS as a fallback. 25
- Live simulation
- The simulation that runs all the time while you draw, colouring wires and moving dots. 25
- Loop gain
- The gain a small signal picks up on one trip around a feedback loop. The Loop gain tab opens the loop at a break point and reports the crossover, phase margin and gain margin. 28.11
- Margins strip
- The line above an AC result with the −3 dB points, crossovers and phase and gain margins. 28.3
- max step
- The largest timestep a Simulate run can take. The Transient tab calls it Maximum timestep. Empty means Auto, a step chosen from the circuit. 27.6
- MCP
- Model Context Protocol: how AI agents connect to BetterSPICE through bspice mcp. 52
- MCU program
- The code of a microcontroller, written in a small language of pins, buses and blocks (
loop,every,when). Edited on the Code tab. 41 - Measurement
- A named result of a run, such as a rise time or a -3 dB frequency, with optional limits that give PASS or FAIL. 29.3
- Meter probe
- A probe that shows its live value in its tag on the schematic. Shift+P. 26.1
- MNA
- Modified nodal analysis: the method both engines use to write the circuit equations. 25
- Model
- The description of how a part behaves that an engine simulates. 44
- Model card
- A one-line SPICE model (.model) for a diode, transistor or JFET. 44.9
- Monte Carlo
- A tolerance analysis that draws every part value at random inside its tolerance and repeats the run. 28.7
- My parts
- Your own parts and symbols, at the top of the library. 46.9
- Noise analysis
- An analysis of the noise at an output over a frequency sweep: the density, the share of each part and the totals. The Noise tab. 28.9
- Net
- A set of pins joined by wires, labels or flags, all at one voltage. 06.4
- Net label
- A name on a wire. Labels with the same name on a sheet are one net. N. 21.3
- Newton iteration
- The repeated solving the engines do at each instant until the voltages agree. 25
- ngspice
- The open-source SPICE simulator that Simulate uses for vendor model files. Ships with the desktop app. 27.12
- Not comparable
- A part ngspice cannot simulate (the MCU, ctrl scripts, behavioural blocks). verify checks it against a closed form or a datasheet window instead, and never counts it as a failure. 58.1
- Overstress warning
- W_OVER_POWER, W_OVER_VOLTAGE, W_OVER_CURRENT or W_DIODE_ACROSS_SOURCE: a part runs over its rating. 27.10
- Pole-zero analysis
- An analysis that finds the poles and zeros of a transfer function at the operating point. The Pole-zero tab. 28.10
- Parameter step
- An analysis repeated once per value of one parameter, curves overlaid. Shift+F7. 28.6
- Part
- What you place on the sheet, such as R1 or U2. 06.5
- Part file
- A .bspart file: a real part with datasheet values, pins and an optional model. 48.3
- Part Wizard
- The eight-step dialog that makes a part file from a datasheet. Ctrl+Shift+N. 45
- Pill
- A state label at the bottom left of the canvas. It shows only Halted. Running and paused are in the status bar. 07.1
- Power flag
- A named supply symbol such as VCC that joins every flag of that name. Shift+G. 21.3
- Probe
- A measurement point you place and save: a net voltage, a pin voltage or a part current. P. 26.3
- PSpice for TI
- Texas Instruments' free PSpice, which Simulate runs hidden for encrypted models. 27.13
- Pull-up
- A resistor from a line to the supply, so it rests high. I²C lines and an open-drain output need one. An MCU input can use its own with
pullup. 41.12 - Quick model
- A model fitted to a few datasheet numbers. Ctrl+Shift+M. 44.6
- Readout digits
- How many significant digits the readouts of the Analysis view and the scopes show, 3 to 9 or Auto: the Digits control beside the trace values. 29.10
- Reference (kept run)
- A result kept with Keep as reference, drawn dashed behind later runs of the same kind. 29.4
- Scope
- The live plot of your probes in the dock, like an oscilloscope. 26.5
- Sense port
- The s+ and s- pins of a CCVS or CCCS: a 0 V branch (an ideal ammeter) whose current controls the source. 31.13
- Share link
- A web address that holds the whole circuit after the #, so whoever opens it sees the circuit running in the viewer. 50.4
- Sheet port
- A connection inside a hierarchical sheet to a pin of its symbol in the parent. Alt+P. 22.9
- Sheet tab
- The ↳ tab of a sheet you opened, after its circuit’s tab. It’s the same document, not a file. 22.7
- SI prefix
- A letter that scales a number: f, p, n, u (µ), m, k, Meg, G, T. 24.5
- Simulate
- The command (F5) that runs a transient you can measure, with vendor models where there are any. Also the analyses. 27
- Split view
- The schematic on top and the Analysis view below. A plain click edits, Alt+click adds a trace. Ctrl+3. 19.5
- Standard value
- A value from a preferred series, such as E12 for resistors. PageUp and PageDown step through them in a number field. 24.5
- Start at rest
- Starting the live simulation at 0 V with every capacitor empty, as at power-on. New circuits start this way. Examples start from the operating point. Simulate › Start at rest (power-on). 25.2
- Status bar
- The line at the bottom: the live engine and whether it’s running or paused, timestep, diagnostics badge and a hint. 19.2
- Subcircuit
- A SPICE model built from other elements (.subckt), as vendors ship for op-amps and regulators. A blank Subcircuit / IC can also be built by hand: double-click it and it becomes a sheet. 22.7
- Symbol
- The drawing of a part on the schematic, with its pins. Stored in .bssym files. 46
- Timebase
- How much circuit time the live simulation covers per real second. Not time per division. 25.3
- Timestep
- The length of one solver step. The live engine uses a fixed one, Simulate an adaptive one up to max step. 25.3
- Tolerance analysis
- Many runs with part values changed inside their tolerances, as Monte Carlo or worst case. It gives the spread, the yield and which parts matter. 28.7
- Transient
- An analysis through time from t = 0 to the stop time. Simulate (F5) runs one. 28.2
- uic
- Use initial conditions: start a transient from the ic values instead of the DC operating point. 27.11
- USB-UART bridge
- A
chipof variantusb_uart(CH340C). Its UART side sends and receives 8N1 bytes, and its USB side is the Console. 38.6 - Vendor model
- A model file from a part's manufacturer, such as TI or ADI, run in ngspice or PSpice. 43
- Viewer
- The browser build that runs a circuit without the desktop app. It opens share links and interactive HTML files. 51
- W_ code
- A warning diagnostic. The run continues. 15
- Worst case
- A tolerance analysis that sets every part to its low or high end and runs the corners. 28.7
- Yield
- The share of tolerance runs whose measurement falls inside the allowed limits. 28.7