Source code coming soon. The GitHub repository is private for now and opens to everyone very soon.
BetterSPICE Beta 0.8.0 Join the beta Download soon
Part II  How do I…?Look-upContentsIndex
09

Task index

Find your goal, in your own words. The grey words are what other people call the same thing, so a search for "Bode" or "bias point" lands here too.

Task index
I want to …Section
Add a datasheet graph to a part (curve, digitize, paste a table, datasheet graph, R_DS(on) vs temperature, fit the model)12.5
Build the inside of a subcircuit myself (edit subcircuit, blank IC, make a block, sub-sheet tab, X1, subckt)10.9
Change the colours or the theme19.7
Check a circuit across component tolerances (tolerance, worst case, min typ max, corner, Monte Carlo, yield, spread, histogram)11.12
Check a power supply: start-up, load step and ripple (ripple, load transient, soft start, overshoot, settling time, regulator, buck converter, LDO)11.11
Choose the model a part uses (assign model, vendor model, SPICE model, change model, model card)12.1
Compare a run with an earlier one (reference, before and after, compare runs, keep a trace, difference)11.14
Draw or edit a symbol (symbol editor, custom symbol, pinout, IC box, bssym)12.6
Export a netlist for another simulator (netlist, ngspice, cir, LTspice, SPICE export)13.5
Find a part or a vendor model in the library (search parts, find a model, part number, MPN, component library)10.6
Find out why every voltage is 0 V14.1
Find the DC operating point of every net (bias point, quiescent point, DC voltages, node voltages, OP)11.9
Find the frequency response and the phase margin (Bode plot, AC analysis, gain margin, stability, -3 dB, bandwidth, cutoff frequency, loop gain)11.6
Fix a run that will not converge (did not converge, E_NEWTON, E_SINGULAR, E_TIMESTEP, halted, convergence, Gear)11.16
Get a model from datasheet numbers (Quick model, fit a model, datasheet values, no model available)12.2
Go back in time in a paused run (scrub, playhead, replay, history, go to a time)11.20
Hand a task to an AI agent and check what it did (Claude, AI, MCP, agent, automate design)13.7
Import a KiCad or EasyEDA Pro design (KiCad, EasyEDA, import schematic, kicad_sch, epro)13.1
Keep sides isolated with their own grounds (isolated ground, floating ground, galvanic isolation, optocoupler, transformer, ISO1, secondary side, second ground, ground domain)10.3
Know which result to trust06.7
Learn every key17
Look at digital signals on the logic analyzer (logic analyzer, digital waveform, bus value, trigger on edge, counter)11.19
Make a part from a datasheet (Part Wizard, new part, custom part, bspart, create component)12.4
Measure time, amplitude and frequency with cursors and stats (delay, rise time, peak to peak, RMS, frequency, duty cycle, measure)11.4
Measure voltage and current at one point (probe, voltage and current, power at a point, both, current probe)11.17
Name nets and use ground and power flags (net label, node name, supply rail, VCC, GND, global label, 0 V reference)10.2
Open an example circuit54
Organise a big circuit with sheets and buses (hierarchy, subcircuit, block, sub-sheet, bus)10.8
Place, rotate and wire parts (add a component, draw a schematic, connect parts, rotate, mirror)10.1
Plot a transfer curve with a DC sweep (DC analysis, transfer characteristic, IV curve, diode curve, sweep a source)11.8
Pop a scope out onto a second monitor19.10
Probe a signal and read it on the scope (scope, oscilloscope, measure voltage, measure current, trace, waveform)11.3
Read a circuit file by hand48.2
Recover unsaved work after a crash19.12
Replace a model that does not run (broken model, retired model, model fails, stand-in, replacement)12.8
Run a model that is encrypted (PSpice, Cadence encrypted, TI model, encrypted model)12.7
Run a program on a microcontroller (MCU, Arduino, firmware, GPIO, blink an LED, code, UART, I2C, SPI, CAN, PWM, ADC)12.3
Run a transient with Simulate (exact transient, time domain, F5, accurate run, tran)11.5
Run simulations from a script (command line, bspice, batch, CI, automation, headless)13.6
Save a picture, a plot or the data (export image, PNG, SVG, CSV, screenshot, copy plot)13.2
Script a control block (PWM, state machine)40
See the spectrum and distortion of a signal (FFT, harmonics, THD, spectrum analyser, noise floor)11.10
See where the power goes in a circuit (energy, power flow, losses, efficiency, heat, where does the power go)11.15
Select, move, copy and undo (duplicate, copy paste, box select, nudge, undo, redo)10.5
Send a circuit to someone who has no BetterSPICE (share, link, viewer, interactive HTML, email a circuit, forum)13.4
Set a pass or fail limit on a result (measurement, pass fail, limit, specification, rise time, overshoot, settling time, efficiency)11.13
Set up ngspice or PSpice57.2
Simulate a transmission line or PCB trace42
Start a circuit from rest or from the operating point (power-on, initial conditions, capacitor starts empty, startup transient, ic, initial voltage, settled state)11.2
Start a new ground domain (new ground, ISO2, another isolated side, rename ground domain, make main ground, ground name)10.4
Stop it halting (didn't converge, E_NEWTON)14.2
Sweep a part value and compare the curves (parameter step, .step, sweep resistor, what if, compare values)11.7
Type exact values and tune them with sliders (change a value, SI prefix, potentiometer, slider range, set resistance)10.7
Understand an E_ or W_ code15
Watch a circuit run, slow it down or pause it (run, pause, timebase, speed, real time, reset)11.1
Write a report (report, documentation, HTML report, print to PDF, in-depth report, datasheet for my design)13.3
Zoom a paused trace to fit the screen (Fit Y, vertical zoom, autoscale, paused scope)11.18